background image

Diesel engine (general
specifications)

Tractor type

714 Vario

716 Vario

718 Vario

720 Vario

722 Vario

724 Vario

Chassis number

738/../

739/../

740/../

741/../

742/../

743/../

Firing order (cylinder # 1 at

flywheel)

1 - 5 - 3 - 6 - 2 - 4

Number of valves

2 inlet and 2 exhaust / cylinder

Compression ratio

18 : 1

Compression pressure

Note:

The compression pressure is

dependent on the starter

speed during the measuring

process and the elevation of

the engine installation

location. Limits cannot be

set exactly.
The compression pressure

measurement is

recommended to serve only

as a comparison of all the

cylinders in an engine.
Where there is more than a

15% deviation, the cause

should be determined by the

removal of the appropriate

cylinder unit.

45 bar

Cooling system

Chassis number 738/../ to 743/../

Cooling type

Fan with Visco coupling

Coolant quantity
(engine content only, without radiator)

approx. 9,2 l

Proportion of cooling system protective inhibitor min./max.

35 vol%/45 vol%

Permitted constant coolant temperature at engine outlet

110 °C

Cooling water pump

1,1 bar

Delivery pressure

Flow rate

196 l/min

Power consumption

1.3 kW/1.77 HP

1. Tractor

FENDT 700 Vario S4 

1-39

X990.005.538.013

Summary of Contents for FENDT 700 Vario S4 Series




















































Reviews: