AFLOWT BUF M Operation Manual Download

Page: 4 / 56

INTRODUCTION

This document covers battery powered ultrasonic flow meter

"AFLOWT BUF M" of BUF-310 version and contains the information
about its design, operation and installation.

Due to continuous improvement of product policy actual flow meter’s

specifications may differ from the data specified in this manual. However,
this will not affect the metrological characteristics and functionality.

LIST OF ABBREVIATIONS

CP
SMC
DN
ER
LCD
PC
PS
PEA
SPS
USS

- Primary converter
- Secondary measuring converter
- Nominal diameter
- Error
- Liquid crystal display
- Personal computer
- Pipeline section
- Electro-acoustic converter (transducer)
- Secondary power source
- Ultrasonic signal

NOTE. Words in the text marked in bold, for example,

Low

, corre-

spond to the items displayed on the flow meter's screen or PC display
when running Monitor BUF (310) program.

* * *

Validation documents are available on website

www.awlowt.com

Summary of Contents for BUF M

























































Search results

Summary of Contents for BUF M

Reviews:

Related manuals for BUF M

Brands by name

Popular brands

AFLOWT BUF M, Operation Manual

Search results

Summary of Contents for BUF M

Reviews:

Related manuals for BUF M

Brands by name

Popular brands