Afag CS 16/30 Manual Download Page 46 | Manualshive

Page: 46 / 49

Afag CS 16/30 Manual Download Page 46

CS 16 - CS 20 - OI-vers. 5.3 gb. 20190312

45

4.1.4 Disassembly and repair

When the module is damaged it can be returned to Afag Automation AG for repair.

CAUTION

The module may only be disassembled when the system is aerated and deactivated. If
pneumatic connections are disconnected when they are under pressure, this may
result in serious personal injury due to fast movements of moving parts.

When can the modules be repaired by the customer?

Wearing parts

can be exchanged by the customer itself when the warranty has expired.

NOTE

All the other faulty parts must exclusively be replaced by company Afag Automation
AG!

When the customer detects that the respective module is still under warranty:

-

The returns the module to company Afag Automation AG for repair.

-

If the warranty has already expired, the customer must decide whether he repairs the module by himself
and orders the wearing parts kit or whether he returns the module to company Afag Automation AG for
repair.

NOTE

Afag offers a reliable repair service. Please note that Afag does not warranty for parts which
were not repaired by Afag Automation AG.

«
...
44
45
46
47
48
...
»

Summary of Contents for CS 16/30


















































Reviews:

No comments