Afag CS 16/30 Manual Download Page 15 | Manualshive

Page: 15 / 49

Afag CS 16/30 Manual Download Page 15

14

CS 16 - CS 20 - OI-vers. 5.3 gb. 20190312

3.1.1 Symbols

Assembly and initial start-up must be carried out by qualified personnel only and according to these instructions.

CAUTION

Indicates a possibly dangerous situation.

Non-compliance with this information can result in damage to property or light to
medium personal injuries.

NOTE

Indicates general notes, useful operator tips and operating recommendations which don't
affect safety and health of the personnel.

3.1.2 General description

This is an incomplete machine

The series of the CS 16-25 Compact Slide is used for the linear, smooth movement of rigidly mounted loads
under the ambient and operating conditions defined, see Technical data.

The CS 16-25 Compact Slide can be installed in the horizontal or vertical position.

Modifications on the CS 16-20 Compact Slide that are not described in these Montage Instructions or have not
been approved in writing by Afag Automation AG are not permitted. In case of improper changes or assembly,
installation, operation, maintenance or repairs, Afag Automation AG rejects all liability.

«
...
13
14
15
16
17
...
»

Summary of Contents for CS 16/30


















































Reviews:

No comments