5
en
6.
Working with the device
6.1
System set-up
6.1.1
Connecting the accessories
Combinations of accessories that are not mentioned in the present
instructions for use may only be employed if they are specifically intended
for the respective application, and if they do not compromise the perfor-
mance and safety characteristics of the products.
All configurations must fulfill the fundamental standard
IEC/DIN EN 60601-1. The person connecting the devices with each other
is responsible for the configuration and must ensure that the fundamental
standard IEC/DIN EN 60601-1 or relevant national standards.
►
Follow the instructions for use of individual accessories.
►
Please address your B. Braun/Aesculap partner or Aesculap Technical
Service with any inquiries in this respect; for a contact address, see
Technical Service.
6.2
Protection against inadvertent activation
The rotational speed control button can be locked to prevent inadvertent
activation of the drill and reamer during a tool/attachment change.
Locking the knob for speed control
2
:
►
Twist the safety catch
3
to position OFF.
The speed control knob
2
is blocked and the product
1
cannot be oper-
ated.
Unlocking the knob for speed control
2
:
►
Twist the safety catch
3
to position ON.
The speed control knob
2
is unlocked and the product
1
can be oper-
ated.
Note
For further information on the drill and reamer, see TA014538 or TA014539
(flyer).
6.3
Coupling and uncoupling of attachment to drill
and reamer
►
Secure drill and reamer
1
against inadvertent activation with the
safety catch
3
, see Protection against inadvertent activation.
Coupling
►
Push the attachment onto drill and reamer
1
until it engages with a
click.
►
Pull at attachment to check that it is securely coupled.
Uncoupling
►
Turn the sleeve
4
in the direction of the arrow
5
and simultaneously
remove the attachment from the drill and reamer
1
.
6.4
Attaching and detaching the tool from the attach-
ment
►
Ensure that the tool connector and attachment type are compatible.
6.4.1
Attachments with quick-action chuck GB623R/GB657R/
GB663R/GB664R/GB665R/GB668R/GB669R/GB670R
Coupling
►
Pull back on the unlocking sleeve
7
.
►
Insert the tool shaft in the correct position up to the stop in the tool
holder
8
of the attachment
6
/
9
.
►
Release the unlocking sleeve
7
.
Tool is attached.
►
Pull at tool to check that it is securely coupled.
Uncoupling
►
Pull back the unlocking sleeve
7
.
►
Remove tool.
6.4.2
Drill attachment keyless Jacobs chuck GB620R
Note
The drill attachment keyless Jacobs chuck GB620R may open during left-
hand rotation of tools (e.g. when pulling out tools).
To operate tools in left-hand rotation, use the Jacobs chuck with key
GB621R, GB639R or GB667R.
Note
If necessary, the key GA031R can be used for coupling and decoupling.
Coupling
►
Rotate the locking sleeve
11
clockwise and open Jacobs chuck.
►
Insert the tool shaft in the correct position up to the st op in the tool
holder
8
of the attachment
10
.
►
Rotate locking sleeve
11
counterclockwise and close Jacobs chuck.
►
Pull at tool to check that it is securely coupled.
WARNING
Risk of infection and contamination!
Product is delivered unsterilized!
►
Sterilize the product before use pursuant to the
operating instructions.
WARNING
Risk of injury and material damage due to inappro-
priate use of tools!
►
Always follow the safety advice and information
given in the instructions for use.
►
When coupling/uncoupling, handle tools with
cutting edges with care.
WARNING
Damage to the product if dropped!
►
Use the products only if they are in perfect tech-
nical condition, see Function check
WARNING
Risk of burns to skin and tissue through blunt tools
or if product has not been maintained properly!
►
Use tools only if they are in perfect condition.
►
Replace blunt tools.
►
Maintain the product properly, see maintenance
guide.
DANGER
Risk of injury due to unapproved configuration
using additional components!
►
Ensure that the classification of all components
used is consistent with the classification of the
product (such as type BF or type CF).
WARNING
Risk of injury when attaching/removing attach-
ments/tools in the ON position through inadvertent
activation of the product!
►
Only attach/remove attachments/tools in the
OFF position.
WARNING
Risk of injury when attaching/removing attach-
ments/tools in the ON position through inadvertent
activation of the product!
►
Only attach/remove attachments/tools in the
OFF position.
