Aerotech Ensemble HLe Hardware Manual Download Page 57 | Manualshive

Page: 57 / 112

background image

Installation and Configuration

Ensemble HLe

2.5.3. Digital Outputs 0-3 (J205)

The digital outputs are optically-isolated and may be connected in sourcing or sinking configurations. The
digital outputs are designed to connect to other ground referenced circuits and are not intended to provide
high-voltage isolation.

The outputs are software-configurable and must be connected in either all sinking or all sourcing mode.

and

illustrate how to connect to an output in current sourcing and current sinking

modes.

The opto-isolator's common connections can be directly connected to the drive's power supply; however,
doing so will effectively defeat the isolation and will reduce noise immunity.

Table 2-28:

Digital Output Specifications

Opto Device Specifications

Value

Maximum Voltage

24 V maximum

Maximum Sink/Source Current

60 mA/channel @ 50°C

Output Saturation Voltage

2.75 V at maximum current

Output Resistance

33 Ω

Rise / Fall Time

250 usec (typical)

Reset State

Output Off (High Impedance State)

Table 2-29:

Port 0 Digital Output Pins on the Auxiliary I/O Connector (J205)

Pin#

Description

In/Out/Bi

7

Digital Output 0

Output

8

Digital Output 1

Output

9

Digital Output 2

Output

15

Output Common

-

16

Digital Output 3

Output

www.aerotech.com

Chapter 2

57

«
...
55
56
57
58
59
...
»

Summary of Contents for Ensemble HLe

















































































































Reviews:

No comments

Related manuals for Ensemble HLe

Brand: J4C Pages: 4

Brand: ABB Pages: 6

Brand: Mamas & Papas Pages: 16

Brand: Campbell Pages: 3

Brand: Danfoss Pages: 37

Brand: Daikin Pages: 44

Brand: Eaton Pages: 2

Brand: Lattice Pages: 23

Brand: Lattice Semiconductor Pages: 2

Brand: Lathem Pages: 4

Brand: tams elektronik Pages: 36

Brand: PACH & COMPANY Pages: 4

Brand: QUNDIS Pages: 2

Brand: VAT Pages: 39

Brand: Samson Pages: 124

Brand: Samson Pages: 86

Brand: VAC Pages: 5

Brand: Multi-Clean Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands