Aerotech Ensemble HLe Hardware Manual Download Page 66 | Manualshive

Page: 66 / 112

background image

66

Chapter 2

www.aerotech.com

2.7. Aeronet Interface (J209/J210)

The Aeronet interface is used to connect discrete Ensemble HLes to make a multi-axis system. The Aeronet
connection requires a shielded CAT-6 Ethernet cable. If a non-shielded cable is used, communication
failures will likely occur.

When connecting a PC using Ethernet or USB to a multi-axis system, you must connect the PC to the
primary Ensemble HLe using the standard Ethernet or USB connectors. Connecting the PC to any of the
secondary units will result in a connection failure.

Any discrete unit is capable of acting as the primary Ensemble HLe. The unit acting as the primary is
dictated by the connection of the Aeronet. A primary drive will only act as an output. A secondary drive (in a
configuration with three or more drives) will act as an input and output. The last drive connected in any
configuration will only act as an input.

Figure 2-37:

Aeronet Connection with Three Discrete Drives

Table 2-42:

Aeronet Cable Part Numbers

Cable Part Number

Length

ENET-CAT6-x

A CAT6 cable; length is x decimeters

1) x = 3, 10, 20, 30, 45, 76, or 90
2) Cable lengths are in decimeters, 10dm = 1 meter = 3.28 feet

Ensemble HLe

Installation and Configuration

«
...
64
65
66
67
68
...
»

Summary of Contents for Ensemble HLe

















































































































Reviews:

No comments

Related manuals for Ensemble HLe

Brand: Eaton Pages: 50

Brand: Bang & Olufsen Pages: 36

Brand: Mad Catz Pages: 4

Brand: Campbell Pages: 3

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 128

VLT DriveMotor FCP 106

Brand: Danfoss Pages: 4

Brand: Samson Pages: 32

Brand: Quantum Pages: 15

Brand: Hach Pages: 2

Brand: Hach Pages: 12

Brand: Hach Pages: 472

Brand: Hach Pages: 64

Brand: V2 ELETTRONICA Pages: 6

Brand: Hach Pages: 210

Brand: Hach Pages: 36

Brand: Hach Pages: 72

Brand: Lamtec Pages: 22

Brand: Nacon Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands