Aerotech Ensemble HLe Hardware Manual Download Page 30 | Manualshive

Page: 30 / 112

background image

30

Chapter 2

www.aerotech.com

2.2.1.2. Unpowered Motor and Feedback Phasing

Disconnect the motor from the controller and connect the motor in the test configuration shown in

.

This method will require a two-channel oscilloscope, a 5V power supply, and six resistors (10,000 ohm, 1/4
watt). All measurements should be made with the probe common of each channel of the oscilloscope
connected to a neutral reference test point (TP4, shown in

). Wave forms are shown while moving

the motor in the positive direction.

Figure 2-5:

Motor Phasing Oscilloscope Example

With the designations of the motor and Hall leads of a third party motor determined, the motor can now be
connected to an Aerotech system. Connect motor lead A to motor connector A, motor lead B to motor
connector B, and motor lead C to motor connector C. Hall leads should also be connected to their respective
feedback connector pins (Hall A lead to the Hall A feedback pin, Hall B to Hall B, and Hall C to Hall C). The
motor is correctly phased when the Hall states align with the Back EMF as shown in (

). Use the

CommutationOffset parameter to correct for Hall signal misalignment.

Figure 2-6:

Brushless Motor Phasing Goal

Ensemble HLe

Installation and Configuration

«
...
28
29
30
31
32
...
»

Summary of Contents for Ensemble HLe

















































































































Reviews:

No comments

Related manuals for Ensemble HLe

Brand: Falcon Pages: 3

Brand: OBaby Pages: 47

Brand: Microchip Technology Pages: 37

Brand: BADODOSECURITY Pages: 8

Brand: Samson Pages: 52

Brand: Samson Pages: 32

Brand: Danfoss Pages: 59

ROBO Cylinder RCP2 Series

Brand: IAI Pages: 5

Brand: jablotron Pages: 2

Brand: Rachio Pages: 2

FOUNDATION 3730-5

Brand: Samson Pages: 132

Brand: Samson Pages: 68

Brand: Samson Pages: 128

Brand: Samson Pages: 68

Brand: X-POWER Pages: 24

Brand: Samson Pages: 80

Brand: Haehne Pages: 44

Brand: Ultratec Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands