Recommended components for E version
Motor:
ø 28 mm outrunner, ca. 150 watts
Battery:
3s LiPo, up to 2,000 mAh
ideal dimensions: 75 x 35 x 20 mm
ESC:
ca. 20 A
Recommended RC equipment
servos up to 10 mm deep
4 servos for Triple speed and R.E.S.
6 servos for Triple thermic
Recommended accessories
CAMcarbon folding prop
9,5×5“ bis 12×7"
(compare with data sheet of your motor)
CN-Spinner ø 30 mm incl. yoke
Oder No.: 7259/03 (3,17 mm shaft)
Oder No.: 7259/04 (4,00 mm shaft)
Alternatively
CN-Spinner ø 33 mm
: 7259/23 (3,17 mm shaft)
Oder No.
: 7259/24 (4,00 mm shaft)
Oder No.
yoke 38 mm
: 7242/21
Oder No.
Wing kits
Wing kit TRIPLE speed
Oder No.: 1128/10
Wing kit TRIPLE R.E.S.
Oder No.: 1128/11
Wing kit TRIPLE thermic
Oder No.: 1128/12
Triple allows you to use different wing designs with the same fuselage. The wings of the Triple series are exchangeable and be employed to
match the weather and your requirements.
This manuall covers the construction of the fuselage (sailplane and E versions) and three different wings. Please note that not all of the sections
in this manual are relevant for your model. The colour-coded guide below will help you identify the sections that apply to your model.
Technical data
TRIPLE speed
TRIPLE R.E.S.
TRIPLE thermic
Oder No.:
1128/00
1128/01
1128/02
Wingspan:
1,780 mm
1,990 mm
2,550 mm
Length saiplane:
1,220 mm
1,220 mm
1,220 mm
Length E version:
1,180 mm
1,180 mm
1,180 mm
Wing area:
ca. 29.5 dm²
ca. 36.3 dm²
ca. 47 dm²
Empty weight (covered model):
ca. 450 g
ca. 480 g
ca. 580 g
RC:
V-tail, aileron (ESC)
V-tail, spoilers
V-tail, aileons, spoilers (ESC)
Triple
speed
r.e.s.
thermic
For sailplane version see section 2 S.
Assemble horizontal formers R-03.1 to R-03.3 with
former R-04 E and formers R-05 to R-09 and insert
in notches in fuselage side. Do not glue! Check
position and alignment of formers. Then remove,
apply glue and glue to fuselage side and each
other.
2
Glue in place the left fuselage side and secure with suitable weights.
Leave to dry.
3
Note:
If you build the E-version of the fuselage, glue two parts R-06 E
to the back of R-06 and make sure the rectangular cut-outs of formers
are properly aligned.
R-01
R-02
R-03.1
R-03.2
R-03.3
R-04 E
R-05
R-07
R-09
R-06
R-08
R-06 E
R-01
R-02
The fuselage sides are made up of a
front (R-01, light ply) and a rear part
(R-02, balsa). Glue parts together on
a flat building board and make sure
the notches for the V-tail support
face upwards.
When dry, sand over the joint very
carefully.
This section is dedicated to the fuselage construction of the E-powered version. Whenever different
parts or tequnices are required for building the sailplane fuselage, a special note will guide you to the
corresponding section and building step.
1
Section I - Fuselage
Section I
Section II
Section III
Section IV
Section V
Section VI
Section VII
Section VIII
Section IX
Fuselage E version
Fuselage sailplane
V-tail
Wings Triple speed
Wings Triple R.E.S.
Wings Triple thermic
Wing centre section
Completing the model
Parts lists
speed, R.E.S, thermic
speed, R.E.S, thermic
speed, R.E.S, thermic
speed
R.E.S
thermic
R.E.S, thermic
speed, R.E.S, thermic
speed, R.E.S, thermic
3
8
10
12
19
23
29
34
35
Section
Contence
Relevant for
Page
das
geniale
3-fach Modell
Tips & Notes
To avoid damage to parts, use a sharp
modelling knife to cut individual parts from
laser sheets.
We recommend our
Balsa-Cutter
Order-No. 8185/00
For building
we recommend our
aero-pick modeller´s pins.
Order-No.: 7855/02
For gluing
we recommend fast
white glue.
Order-No.: 7638/10 (225 g)
R-06
2
3
