manualshive.com logo in svg

AERMEC HMI-1, User Manual

Share
Download
AERMEC HMI-1 User Manual Download Page 29

29

Label

Meaning

State

SG signal

SG signal

On/Off

EVU signal

EVU signal

On/Off

SG

SG control command

Switch-off command 

/ Standard operation / 

Switch-on signal / Switch-

on command

7.2    VIEWING THE STATUS OF THE UNIT PARAMETERS (PARAMETER)

At the “VIEW” page, by touching “Parameter”, it is able to view each parameter of the 
unit, as shown in the figure below:

Param. view (1/4)

T-outdoor: 0.0°C

T-suction: 0.0°C

T-discharge: 0.0°C

T-defrost: 0.0°C

T-water in PE: 0.0°C

 Viewable  Parameters

Label

Meaning

T-outdoor

Indicates the external air temperature detected by the unit

T-suction

Indicates the temperature on the compressor inlet

T-discharge

Indicates the compressor delivery temperature

T-Defrost

Indicates the temperature for the defrosting cycle 

T-water in PE

Indicates the temperature of the water entering the plate heat exchanger

T-water out PE

Indicates the temperature of the water leaving the plate heat exchanger

T-optional water sen.

Indicates the temperature of the water leaving the optional heater (paragraph "6.8 Setting an additional heater (Optional 

E-heater) p. 22")

T-tank ctrl.

Indicates the temperature measured in the compatible Aermec accessory tank

T-economizer in

Indicates the temperature on the economiser inlet

T-economizer out

Indicates the temperature on the economiser outlet

T-floor debug

Indicates the set temperature for radiant floor debug (paragraph "6.11 Setting the pre-heating procedure for radiant panels (Floor 

debug) p. 23")

Debug time

Indicates the set time for radiant floor debug (paragraph "6.11 Setting the pre-heating procedure for radiant panels (Floor 

debug) p. 23")

T-gas pipe

Indicates the temperature detected on the gas side of the cooling circuit

T-liquid pipe

Indicates the temperature detected on the liquid side of the cooling circuit

T-auto mode

Indicates the current set-point temperature, calculated using the climatic curve (paragraph "4.6 Energy-saving mode p. 11")

T-remote room

Indicates the room temperature detected by the probe (paragraph "6.9 Setting the installation of the remote room temperature probe 

(Ambient sensor) p. 22")

Dis. pressure

Indicates the compressor delivery pressure value

Summary of Contents for HMI-1





































Reviews:

No comments

Brands by name

Popular brands

Load more brands