Aerco INNOVATION INN1060 User Manual Download Page 31 | Manualshive

Page: 31 / 200

background image

Chapter 3

Innovation Series Water Heaters

GF-128

Operation

USER MANUAL

OMM-0079_0B

07/21/11 AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, NY 10913

•

Ph: 800-526-0288

Page

31

of

200

3.3

CONTROL PANEL MENUS

The Control Panel incorporates an extensive menu structure which permits the operator to set up, and
configure the unit. The menu structure consists of five major menu categories which are applicable to this
manual. These categories are shown in Figure 3-2. Each of the menus shown, contain options which
permit operating parameters to be viewed or changed. The menus are protected by a password levels to
prevent unauthorized use.

Prior to entering the correct password, the options contained in the Operation, Setup, Configuration and
Tuning Menu categories can be viewed. However, with the exception of Internal Setpoint Temperature
(Configuration Menu), none of the viewable menu options can be changed.

Once the valid level 1 password (159) is entered, the options listed in the Setup. Configuration and
Tuning Menus can be viewed and changed, if desired.

3.3.1

Menu Processing Procedure

Accessing and initiating each menu and option is accomplished using the Menu Keys shown in Figure 3-
1. Therefore, it is imperative that you be thoroughly familiar with the following basic steps before
attempting to perform specific menu procedures.

1. The Control Panel will normally be in the Operating Menu and the VFD will display the current unit

status. Pressing the ▲ or ▼ arrow key will display the other available data items in the Operating
Menu.

2. Press the

MENU

key. The display will show the Setup Menu, which is the next menu category shown

in Figure 3-2. This menu contains the Password option which must be entered if other menu options
will be changed.

3. Continue pressing the

MENU

key until the desired menu is displayed.

4. With the des

ired menu displayed, press the ▲ or ▼ arrow key. The first option in the selected menu

will be displayed.

5.

Continue to press the ▲ or ▼ arrow key until the desired menu option is displayed. Pressing the ▲
arrow key will display the available menu options in the Top-

Down sequence. Pressing the ▼ arrow

key will display the options in the Bottom-Up sequence. The menu options will wrap-around after the
first or last available option is reached.

6. To change the value or setting of a displayed menu option, press the CHANGE key. The displayed

option will begin to flash. Press the ▲ or ▼ arrow key to scroll through the available menu option
choices for the option to be changed. The menu option choices do not wrap around.

7. To select and store a changed menu item, press the ENTER key.

«
...
29
30
31
32
33
...
»

Summary of Contents for INNOVATION INN1060









































































































































































































Reviews:

No comments

Related manuals for INNOVATION INN1060

Brand: A.O. Smith Pages: 68

Brand: Garanterm Pages: 20

Brand: Marco Pages: 43

CHITWOOD SMOKE BROILER KC-24

Brand: Jade Pages: 10

Brand: Biasi Pages: 88

Brand: Immergas Pages: 8

ECONOFLAME R6000

Brand: STOKVIS ENERGY SYSTEMS Pages: 46

Brand: Clean Energy Pages: 54

Platinum Combi HE A

Brand: Baxi Pages: 8

Brand: Baxi Pages: 46

EBE Express Series

Brand: Ecoboil Pages: 4

EB Rapid Series

Brand: Ecoboil Pages: 4

Brand: Viadrus Pages: 32

Brand: Ideal Boilers Pages: 64

Brand: Unical Pages: 28

Brand: Burnham Pages: 132

ACB20 ML-135285

Brand: ITW Food Equipment Group Pages: 9

DOMIcondens HE 26 C

Brand: Ferroli Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands