background image

AMR Integrated Water Heaters (Supplement to GF-146) 

CHAPTER 4: INSTALLATION - PIPING 

4.8  Condensate Disposal 

WARNING! 

 

The condensate trap,  as  shown in  Figure  4-8, item  “B”,  MUST be 

filled  with  water  or  combustion  gases  will  enter  the  room.  The 

condensate neutralizer tank must be installed into the unit, exactly 

as shown in Figure 4-8. Do NOT remove the condensate neutralizer 

tank from its position while the unit is in operation, as this  will result 

in  combustion  gases  entering  the    room,  which  can  result  in 

excessive levels of carbon monoxide. 

The unit is equipped with a condensate neutralizer tank for the evacuation of condensate and to 

prevent the leakage of combustion products. The condensate drains from the flue exhaust outlet 

“A” (Figure 4-8) through pipe to condensate neutralizer tank, drains through hose “C” and then out 

the  drain  pipe  (Figure  4-9),  and  empties  into  the  floor  drain  or  drain  pan  (Figure  4-9).  The 

condensation disposal system must: 

  slope  the  condensate  tubing  down  and  away  from  the  water  heater,  without  any 

subsequent  elevation,  into  a  drain  or  drain  pan  (See  Figure  4-9).  Condensate  from 

the water heater will be slightly acidic (around pH 4). The  neutralizing tank (see Figure 

4-8, item “B”) is built into the water heater and will neutralize the  condensate products; 

  be  carried  out  with  a  pipe  with  an  internal  diameter  equal  to  or  greater  than  3/4 

inches  (19 mm); 

  be installed in such a way so as to avoid the freezing of the liquid; 

  never discharge into gutters or rain collectors; 

  be  properly  pitched  towards  the  point  of  discharge  avoiding  high  points (Figure 4-9), 

which  could  place the condensate system under pressure; 

 

 

Figure 4-8: Condensate Neutralizer Tank

 

= Connected to the Flue Exhaust 

= Condensate Neutralizer Tank 

= Condensate Drain Outlet 

= Tank Cover 

 

Page 

26

 of 

52

 

 

AERCO International, Inc. 

 100 Oritani Dr. 

  Blauvelt, NY 10913  

OMM-0106_0A

 

PRI - 07/22/15

 

Ph.: 800-526-0288 

GF-146-IR 

 

Summary of Contents for GF-146-IR





















































Reviews: