Aerco GF-146-IR Installation, Operation, Maitenance Manual Download

Page: 15 / 52

AMR Integrated Water Heaters (Supplement to GF-146)

CHAPTER 3: INSTALLATION - SITE

3.3 Safety Concerns

WARNING!

Do not store any ﬂammable materials or liquids in the immediate

vicinity of the water heater.

3.4 Closet and Alcove Installation

AM water heaters are not approved for installation in a closet or in an alcove site.

3.5 Clearances for Installation and Servicing

Figures 3-1 shows the minimum clearances required for installation and servicing.

Figure 3-1: AMR Integrated Recommended Minimum Service Clearances

NOTE

Service clearances are minimum required clearances for ease of

access, but larger service clearances are always preferred.

3.6 Clearances to Combustible Material

This unit may be installed directly onto a floor of combustible material with the following

clearances:

Table 3-1: Unit Installation Clearance Dimensions

COMPONENT

CLEARANCE DISTANCE

Ceiling

2 inches (51 mm)

Front

2 inches (51 mm)

Rear

2 inches (51 mm)

Sides

2 inches (51 mm)

Floor

0 inches (0 mm)

Concentric vent

0 inches (0 mm)

Split vent (two pipes) ﬁrst 3 feet from the water heater

1 inch (25 mm)

Split vent (two pipes) after 3 feet from the water heater

0 inches (0 mm)

Water heater piping

¼ inch (7 mm)

OMM-0106_0A

AERCO International, Inc.

•

100 Oritani Dr.

•

Blauvelt, NY 10913

Page

GF-146-IR

Ph.: 800-526-0288

PRI - 07/22/15

Summary of Contents for GF-146-IR





















































Search results

Summary of Contents for GF-146-IR

Reviews:

Related manuals for GF-146-IR

Brands by name

Popular brands

Aerco GF-146-IR, Installation, Operation, Maitenance Manual

Search results

Summary of Contents for GF-146-IR

Reviews:

Related manuals for GF-146-IR

Brands by name

Popular brands