CONTROL PANEL OPERATING PROCEDURES
3-4
3.3 CONTROL PANEL MENUS
The Control Panel incorporates an extensive
menu structure which permits the operator to set
up, and configure the unit. The menu structure
consists of five major menu categories which are
applicable to this manual. These categories are
shown in Figure 3-2. Each of the menus shown,
contain options
which
permit
operating
parameters to be viewed or changed. The
menus are protected by a password levels to
prevent unauthorized use.
Prior to entering the correct password, the
options contained in the Operation, Setup,
Configuration and Tuning Menu categories can
be viewed. However, with the exception of
Internal Setpoint Temperature (Configuration
Menu), none of the viewable menu options can
be changed.
Once the valid level 1 password (159) is
entered, the options listed in the Setup.
Configuration and Tuning Menus can be viewed
and changed, if desired. The Combustion Cal
Menu is protected by the level 2 password which
is used in Chapter 4 to perform combustion
calibration prior to service use.
3.3.1 Menu Processing Procedure
Accessing and initiating each menu and option
is accomplished using the Menu Keys shown in
Figure 3-1. Therefore, it is imperative that you
be thoroughly familiar with the following basic
steps before attempting to perform specific
menu procedures.
1. The Control Panel will normally be in the
Operating Menu and the VFD will display the
current unit status. Pressing the
▲ or ▼
arrow key will display the other available
data items in the Operating Menu.
2. Press the
MENU
key. The display will show
the Setup Menu, which is the next menu
category shown in Figure 3-2. This menu
contains the Password option which must be
entered if other menu options will be
changed.
3. Continue pressing the
MENU
key until the
desired menu is displayed.
4. With the desired menu displayed, press the
▲ or ▼ arrow key. The first option in the
selected menu will be displayed.
5. Continue to press the
▲ or ▼ arrow key
until the desired menu option is displayed.
Pressing the
▲ arrow key will display the
available menu options in the Top-Down
sequence. Pressing the
▼ arrow key will
display the options in the Bottom-Up
sequence. The menu options will wrap-
around after the first or last available option
is reached.
6. To change the value or setting of a
displayed menu option, press the
CHANGE
key. The displayed option will begin to flash.
Press the
▲ or ▼ arrow key to scroll
through the available menu option choices
for the option to be changed. The menu
option choices do not wrap around.
7. To select and store a changed menu item,
press the
ENTER
key.
OPERATING
LEVEL 1 PWD
SETUP
CONFIGURATION
TUNING
LEVEL 2 PWD
COMBUSTION CAL
CALIBRATION
(NOT USED IN THIS O & M)
DIAGNOSTICS
(NOT USED IN THIS O & M)
Figure 3-2. Menu Structure
Summary of Contents for Benchmark 3.0LN Series
