USER CODES / CARDS FOR OUTPUT 1 & 2 (Locations 10 & 20)
LOCATIONS MEDIA USER ID CARD / USER CODE VALIDATION
(1) LOCATIONS (User Groups)
– Group 1 – 1,000 User Codes / Cards for controlling Output 1
– Group 2 – 100 User Codes / Cards for controlling Output 2
(2) MEDIA (Operation Media)- please also see page 12 for more information of their security level
– Cards Only – 125Khz Proximity EM Card
– User Codes Only – 4-8 Digits
– Cards + Secondary User Code(s) –
See Note (a)
– Cards + Common User Code –
See Note (b)
– Delete Cards / User Codes from the selected User ID –
See Note (c)
– Group Clearing. Clear all the User Codes & Cards of the selected User Group
(3) USER ID (The IDs of The User Codes and Cards)
–
– 1,000 User IDs for the User Codes & Cards in User Group 1 (Output 1)
–
– 100 User IDs for the User Codes & Cards in User Group 2 (Output 2)
(4) CARD / USER CODE
Read EM Card
or
key in User Code
into each assigned User ID.
(5) VALIDATION
Press the
key once. Two-beep confirms the entry.
NOTE:
(a) The Secondary User Code is a user code putting after a card in programming. It can be a
proprietary user code for each user card or a code repeatedly used for a group of user cards as
group user code (e.g. for a group of staff working in the same department).
(b) The Common User Codes for the Output 1 & 2 have been programmed first at Locations 03 & 04
respectively. It is not necessary to key in the code again in programming here and it will follow
the card automatically after the card is read.
(c) Deletion of an User Code or Card (if the card was lost) can be done by keying-in its ID number.
For deleting an existing cards, simply read the card once and confirm. It does not require the ID
number. The Card includes the combinations of (1) Card Only, (2) Card + Secondary User Code
and (3) Card + Common User Code.
(1)
(2)
(5)
(4)
(3)
Location. Clearing takes few seconds to a minute.
EGRESS DELAY , WARNING AND ALARM (Location 90)
(1) LOCATION
Key in Location
(2) CONFIGURATIONS OF THE EGRESS WARNING
Key in the number to enable 1 of the 6 configurations described below:
---
Momentary Contact Mode without Warning -- (Default)
---
Momentary Contact Mode with Warning Beep
---
Holding Contact Mode without Warning
---
Holding Contact Mode with Warning Beep
(3) EGRESS DELAY TIMER
---
No Delay – (Default)
Output 1 activates instantly (the door is released instantly) when the Egress Button is pressed.
–
---
Egress Delay Timing
Put a number of 1 to 99 into the box to enable the Egress Delay. The number is the time in second,
which starts to count when the Egress Button is pressed. Output 1 activates (the door is released)
when the delay time reaches.
CONFIGURATIONS
VALIDATION
DELAY TIME
LOCATION
-
or
-
Press the Button once. No warning or alarm is given during Egress Delay.
Good for silent area. The people have to wait for the door open until the delay time reaches.
Press and hold the Button. The system gives Warning Beeps during Egress Delay.
Good for the place required attention. The keypad beeps while the button is kept pressed during
the people are waiting for the door open.
(2)
(4)
(3)
(1)
Press and hold the Button. No warning or alarm is given during the Egress Delay.
Good for the silent area. The people require to press & hold the button until the delay time
reaches for the door open.
Press the Button once. The system gives Warning Beeps during the Egress Delay.
Good for the place required attention. The keypad beeps during the people are waiting for the
door open.
