ON-BOARD LED INDICATORS
RED / GREEN (Right)
---
AMBER (Centre)
---------
RED (Left)
----------
PACIFIER TONES & THE LED SIGNALS
The buzzer and the amber LED indicator give following tones and signals respectively for system
status:
DA-2801
DA-2800
Connection Terminal
The Split-decoders (Optional)
-
AL
ARM O/P
-
KEY ACT O/
P
-
N.O
.
-
COM
-
N.C
.
-
N.O
.
-
COM
-
N.C
.
-
N.O
.
-
COM
-
N.C
.
-
T
AMPER
-
GND(
-
)
-
DOOR SENS
-
O/P 1 INHI
B
-
IN
T. L
OCK
-
DU OUT
-
DOOR BELL IN
-
EG IN
-
DATA
I/O
-
KEYP
AD PWR
-
GND(
-
)
-
12-24V DC
OPEN COLLECTOR OUTPUT
OPEN COLLECTOR OUTPUT
1A RE
LA
Y DRY CONT
ACT
S
FOR AU
XILIARY CONTROL
1A REL
AY
DRY CONT
ACT
S
FOR AU
XILIARY CONTROL
5A RE
LA
Y
DRY CONT
ACT
S
FOR DOOR STRIKE
OPEN COLLECTOR OUTPUT
OPEN COLLECTOR OUTPUT
INPUT/OUTPUT FOR SPLIT
-DECODED SIGNAL
S
POWER OUTPUT FOR KEYP
ADS
COMMON GROUND
POWER INPUT FOR SYSTEM
N.C. S
W
COMMON GROUN
D
N.C. S
W
N.
O. S
W
N.
O. S
W
N.
O. S
W
OUTPUT 1
OUTPUT 2 OUTPUT 3
Standard Decoder
Decoder with RF Remote Control
It lights up in Green for Output 1 activation; Red for Output 1 inhibited
and flashing during inhibition paused.
It flashes in Standby. It shows the system status in synchronization
with the beep tones. The standby flashing can be OFF with
programming. See Location 73 for the details.
It lights up in Red for output 2 activation.
STATUS
TONES *
AMBER LED
1) In Programming Mode
-----
ON
2) Successful Key Entry
1 Beep
1 Flash
3) Successful Code / Card Entry
2 Beeps
2 Flashes
4) Unsuccessful Code / Card Entry
5 Beeps
5 Flashes
5) Power Up Delay
Continuous Beeps
Continuous Flashes
6) Output Relay Activation **
1 Second Long Beep
7) In Standby ***
-----
1 Flash in 1 Second Interval
8) System Refreshing
-----
Fast Flashes for 2.5 Minutes
Continuous 3 Fast Beeps
/5 secs
-----
Continuous 1 Beep/5 secs
11) Real -time-clock stopped after
power failure
10) Keypad link-up with Decoder Failed
)
9
Card or Code Already Stored in
System
1 Long Beep
-----
-----
-----
NOTE:
*
* *
* * *
JUMPER FOR BACK-LIT SELECTION
1)
Full Back-lit
---
2)
Auto Back-lit
---
3) OFF
---
All Pacifier Tones can be ON or OFF through the programming option at Location 71
The Output Relay Activation beep can be selected through the programming option at
Location 72
The Standby flashing can be ON or OFF through the programming option at Location 73
The keypad gives dim backlit in standby. It
turns to full backlit when a key button is
pressed, then back to dim backlit 10
seconds after the last key button is
pressed.
The backlit is OFF in standby. It turns to
full backlit when a key button is pressed,
then back to OFF 10 seconds after the last
key button is pressed.
Back-lit function disabled.
OTHER FACILITIES
BACK-LIT
JUMPER
IMPORTANT NOTE
The optional Auxiliary Readers, Reader-keypads and Split-decoders are DC
operation. It is necessary to power the whole system with DC power supply if the
Master Keypad is working with them for system expansion, even it is an AC/DC
Version keypad
