AEG KO-LAVAMAT 88830 User Information Download | Manualshive

Page: 44 / 56

background image

Setting up and connection instructions

44

SETTING UP AND CONNECTION
INSTRUCTIONS

Safety Instructions for Installation

• Do not tilt the washing machine onto its front or onto its right side

(looking from the front). Electrical components could get wet!

• Check the washing machine for transport damage. Never connect a

damaged unit. Consult your supplier in the event of damage.

• Ensure that all parts of the transport safeguard have been removed

and that the splash guard is fitted to the unit, see ”Removing the
Transport Safeguard”. Otherwise, damage to the unit or to adjacent
furniture could occur during spinning.

• Always insert the plug into a correctly installed PE socket.

• In the case of permanent installation: A permanent installation may

only be made by an authorised specialist.

• Before putting the unit into operation, ensure that the rated voltage

and current type shown on the unit's rating plate are the same as the
mains voltage and current type at the installation location. The
required electrical fuse is also shown on the rating plate.

• The mains cable may only be replaced by the Customer Service or by

an authorised specialist.

«
...
42
43
44
45
46
...
»

Summary of Contents for KO-LAVAMAT 88830

























































Reviews:

No comments

Related manuals for KO-LAVAMAT 88830

Brand: Gaggenau Pages: 31

Brand: Hoover Pages: 17

ODW 60032 FS A2

Brand: OK. Pages: 27

Brand: Hanseatic Pages: 88

Brand: Gaggenau Pages: 48

Brand: Wascomat Pages: 132

Brand: Alliance Laundry Systems Pages: 64

3VT913NA - annexe 1

Brand: BALAY Pages: 2

DDW1802 - 14352

Brand: Danby Pages: 12

Brand: Fisher & Paykel Pages: 6

Brand: Hoover Pages: 32

WF45N6300A Series

Brand: Samsung Pages: 58

Brand: Samsung Pages: 68

Brand: Samsung Pages: 124

Brand: Samsung Pages: 124

Brand: Samsung Pages: 124

WF45N5300A Series

Brand: Samsung Pages: 136

WF42H5500A SERIES

Brand: Samsung Pages: 132

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands