AEG KO-LAVAMAT 88830 User Information Download | Manualshive

Page: 35 / 56

background image

Instructions for use

35

The drain pump for the
washing machine runs
constantly - even when
the appliance is
switched off.

The Aqua Control anti-flood
system has been activated.

Turn off the tap, then
remove the plug from the
mains and inform Customer
Service.

Conditioner was not
washed in, compart-
ment

æ

for care

agents is filled with
water.

Softener insert in the com-
partment for care agent ist
not correctly attached or is
blocked.

Clean the detergent drawer
and firmly attach the soft-
ener insert.

Washing heavily
creased.

Probably too mush washing
put in.

Pay attention to the maxi-
mum filling quantity (see
Program tables). Select the
program EASY IRON (SANS
REPASSAGE) for easy-care
fabrics.

Washing not well spun.
Residual water still vis-
ible in the drum.

Error code

(2

appears

.

Drainage hose bent.

Remove the bend.

The maximum pump height
(discharge height 1m from
the positioned surface of the
appliance) is exceeded.

Contact your customer serv-
ice. For pumping heights
over lm he can offer you a
conversion kit as a special
accessory.

Solution pump blocked.

Switch off the unit and pull
out the mains plug. Clean
the solution pump.

If a siphon is connected:
Siphon blocked.

Clean the siphon.

The filling door cannot
be opened with the
unit switched on.

The door is locked for safety
reasons (the DOOR (PORTE)
display is not illuminated).

Wait until DOOR (PORTE) is
illuminated in green.

The program saving function
is set.

Cancel the program saving
function (see "Program Sav-
ing").

The washing machine is in
the stand-by mode.

Press DOOR (PORTE) button
again.

Problem

Possible Cause

Remedy

«
...
33
34
35
36
37
...
»

Summary of Contents for KO-LAVAMAT 88830

























































Reviews:

No comments

Related manuals for KO-LAVAMAT 88830

Brand: Haier Pages: 6

Brand: Haier Pages: 12

Brand: Haier Pages: 34

Brand: Haier Pages: 12

Brand: Haier Pages: 11

Brand: Haier Pages: 28

Brand: Haier Pages: 12

Brand: Fagor Pages: 22

Brand: Gaggenau Pages: 22

Brand: Gaggenau Pages: 34

Brand: Hoover Pages: 28

Brand: Kärcher Pages: 112

Brand: Smeg Pages: 36

Brand: Mancorp Pages: 13

Brand: Fisher & Paykel Pages: 12

Brand: Indesit Pages: 24

Brand: Buffalo Pages: 20

Brand: Hotpoint Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands