AEG KO-LAVAMAT 88830 User Information Download | Manualshive

Page: 27 / 56

background image

Instructions for use

27

4.

Turn the program selector to OFF (ARRET).

5.

After washing, pull out the washing detergent drawer slightly so that it
can dry out. Only lean the door against the washing machine so that
the latter can air out.

3

Too much detergent was used in the just finished
program if OVER-DOSED (SURDOSAGE) is illuminated.
Observe the dosing recommendations of the detergent
manufacturer as well as the filling quantity for the
next wash.

Attention!

If the washing machine is not used for a long time:

Close the water tap and disconnect the washing machine from the
electricity mains. (Aqua Control water protection with Aqua Alarm
does not operate if the power supply is interrupted.)

«
...
25
26
27
28
29
...
»

Summary of Contents for KO-LAVAMAT 88830

























































Reviews:

No comments

Related manuals for KO-LAVAMAT 88830

Brand: Kärcher Pages: 17

K 5 Full Control

Brand: Kärcher Pages: 16

Brand: Kärcher Pages: 12

K 3.800 eco!ogic

Brand: Kärcher Pages: 244

Brand: Kärcher Pages: 64

Brand: Kärcher Pages: 16

Brand: Kärcher Pages: 212

Brand: Kärcher Pages: 48

Brand: Kärcher Pages: 344

HDS-E 3.3/25-4M Ec

Brand: Kärcher Pages: 52

Brand: Kärcher Pages: 417

Brand: Kärcher Pages: 13

Brand: Kärcher Pages: 474

Brand: Kärcher Pages: 428

HDS 1.7/12 U Ed

Brand: Kärcher Pages: 48

Brand: Kärcher Pages: 352

Brand: Kärcher Pages: 11

HD 6/11-4 M Plus

Brand: Kärcher Pages: 372

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands