background image

Fig. 6

Fig. 5

CAUTION!

 Use only manufacturer’s approved 

vacuum filters and filters bags. Before attempting 

to use or before cleaning with this vacuum, be sure 

that you fully understand the instructions for setting 

up or cleaning/changing filters.

WARNING!

 If filters are contaminated or 

damaged, they must be replaced prior to 

performing wet vacuuming operations.

10. For wet vacuum cleaning, remove the pre-filter, HEPA filter 

and collection bag, install the supplied foam filter. (Fig. 11) 

11. Place the power head back on the tank, aligning the top 

section with the latches, and hook the latches. (Fig. 12)

12. Insert the locking end of the hose into the vacuum port and 

turn to lock in to place. (Fig. 13)

13. Choose the desired accessories and push onto the suction 

tube. (Fig. 14)

1. Verify that the power cord is disconnected from the mains 

power source. 

2. Undo the latches. (Fig. 1)
3. Lift the power head off the tank. (Fig. 2)
4. Remove the contents from inside the tank, make sure you 

have all contents as listed in component list. (Fig. 3)

5. Turn the tank upside down and insert the two caster feet 

into the front slots on the base. Apply downward pressure 

to each caster. Casters will "snap" into place when installed 

properly. 

     Verify that the casters are mounted correctly. (Fig. 4)
6. Insert the wheel axle into the base. Insert washer onto the 

axle followed by rear wheel and insert washer again. Insert 

the ‘R’ locking pin into the hole on the end of the axle to lock 

the wheel. Snap the hub cap on to the wheel. Repeat the 

same steps at the other end of the axle. (Fig. 5)

7. Spread the push / pull main handle. Spin the power cable 

hook to fix the handle in place. (Fig. 6)

8. Your vacuum comes ready for dry vacuum cleaning. If 

HEPA filter and pre-filter are not installed refer to page  8 

for filter installation. (Fig. 7-9)

9. Fit collection bag flange onto the inlet stub, taking care not 

to damage the bag. (Fig. 10)

UNPACKING YOUR WET/DRY VACUUM & GENERAL 

ASSEMBLY

5

GENERAL ASSEMBLY INSTRUCTIONS

14

15

13

13

17

16

16

16

16

Fig. 9

Fig. 8

Fig. 7

Fig. 4

Fig. 3

Fig. 2

Fig. 1

Fig. 10

Fig. 11

Summary of Contents for AVC-1530-G

















Reviews: