background image

WARNING!

 Always switch off and unplug the 

machine from the mains power source before 

assembling, opening, emptying the dirt tank, 

before connecting/disconnecting the attachments, 

or carrying out maintenance or troubleshooting 

checks.

IMPORTANT!

 If the hose or tools are blocked, switch off the 

cleaner and remove the blockage(s) before re-starting your 

machine.

PLEASE KEEP THESE INSTRUCTIONS FOR FURTHER 

USE.

• 

Never vacuum up hot ashes, pointed or sharp objects.

• 

Never use the appliance in damp rooms.

• 

Don’t use the appliance without a dust bag (an exception is 

wet vacuuming or with the cartridge filter). Make sure that 

the dust bag is inserted into the appliance correctly.

• 

When using the appliance, make sure that no hair, clothing, 

or members are drawn in.

• 

Keep the vacuum cleaner away from heat sources such as 

radiant heaters, ovens, and so on.

DAMAGE TO THE VACUUM CLEANER CAUSED AS A 

DIRECT RESULT OF NOT ADHERING TO THE GENERAL 

SAFETY INFORMATION AND THE INSTRUCTIONS IN 

THIS USER GUIDE INVALIDATES THE WARRANTY.

IMPORTANT!

 Cleaning filters and replacing them regularly 

maintains vacuum performance. AEG recommends that your 

filters should be checked, cleaned and replaced periodically.

40. Electrical power should be supplied via a residual current 

device (RCD) with a tripping current of not more than 

30mA.

41. Only use a weather proof extension cord. Check the 

extension cord before every use for damage. Always 

uncoil the extension cord during use because coiled cords 

can overheat. Damaged extension cords should not be 

repaired, they should be replaced with an equivalent type.

GENERAL SAFETY PRECAUTIONS 

FOR USING WORKSHOP VACUUM

ADDITIONAL SAFETY INSTRUCTIONS

FOR  WORKSHOP VACUUM

4

Summary of Contents for AVC-1530-G

















Reviews: