background image

6

WARNING!

 If filters are contaminated or damaged, 

they must be replaced prior to performing wet 

vacuuming operations.

DO NOT USE THE HEPA FILTER FOR WET VACUUMING.

A: Function switch ON/OFF switch
B: Outlet-socket

SWITCHING ON/OFF

WARNING!

 BE SURE TO READ, UNDERSTAND 

ALL WARNINGS AND INSTRUCTIONS IN THE 

MANUAL BEFORE USE. DO NOT VACUUM IN 

AREAS WITH FLAMMABLE GASES, VAPORS, 

OR EXPLOSIVE DUSTS IN THE AIR.

CAUTION!

  NEVER operate the vacuum cleaner 

without all of the filters installed. This includes the 

HEPA filter, pre-filer and collection bag. Motor 

damage, lose of operating efficiency and recirculation 

of hazardous material into the work area will take 

place if not installed. Make sure plug is disconnected 

before assembly.

    removed and in upside down position, make sure the filter 

is pushed in until it stops against the power head and the 

filter cap is installed. (Fig. 15 & 16)

3.  Place the pre-filter into the tank and press the hoop 

downward until it stops against the tank edge. (Fig. 17) 

4. For improved dust collecting, fit collection bag flange onto 

the inlet stub, taking care not to damage the bag. (Fig. 18)

5. Place the power head back on the tank, and secure it in 

place using the latches. (Fig. 19)

1. Verify that the power cord is disconnected from the mains 

power source. 

6. Insert the locking end of the hose into the vacuum port and 

lock in place. Push the required attachment onto the free 

end of the hose or extension. (Fig. 20)

7. Plug in the power cord into the mains power source. 
8. Turn the motor on by turning the switch to the ‘I’ ON 

position. 

9. Once you have completed vacuuming, flip the switch to the 

‘O’ OFF position and unplug the power cord from the  mains 

power source.

FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE 

NOT LIMITED TO; LIGHTER FLUID, SOLVENT TYPE 

CLEANERS, OIL-BASE PAINTS, GASOLINE, ALCOHOL OR 

AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT 

ARE NOT LIMITED TO; COAL, MAGNESIUM, GRAIN OR 

GUN POWDER. TO REDUCE THE RISK OF HEALTH 

HAZARDS FROM VAPORS OR DUST, DO NOT VACUUM 

TOXIC MATERIALS.

DRY VACUUM

Fig. 13

Fig. 15

Fig. 16

Fig. 17

Fig. 18

Fig. 19

Fig. 20

Fig. 12

Fig. 14

DRY-VACUUM OPERATION

2. In order to prepare your vacuum for dry vacuuming, verify 

that the HEPA filter is securely mounted. With power head

Summary of Contents for AVC-1530-G

















Reviews: