background image

2. Never immerse the appliance in liquids and be aware of 

sharp edges that may damage it. Never use the appliance 

with wet or damp hands. Unplug it immediately if the 

appliance becomes wet or damp when it is running. Don’t 

immerse the appliance in water.

GENERAL SAFETY PRECAUTIONS FOR USING WORKSHOP VACUUM

1. This appliance is designed solely for use in the private 

sector and for the designated purpose. The appliance is 

not suitable for commercial use. Don’t use the appliance 

outdoors (unless it has been specifically designed for 

use outdoors). Don’t subject the appliance to heat, direct 

sunshine or very high moisture (e.g., rain).

21.  Children, disabled persons, and the aged are often not 

aware of the dangers that can result from handling electric 

appliances. The above mentioned persons and untrained 

persons must never work with this electrical appliance.

22. When cleaning or removing the appliance, always switch it 

off. Pull the plug out of the receptacle, if you are not going 

to use the appliance for an extended period of time. Never 

pull on the cable to unplug the appliance, rather pull on the 

plug itself. Also, remove any special accessories from the 

appliance.

23. Always keep the appliance clean. Don’t use any solvents or 

cleaners that may damage or be harmful to the appliance 

or user.

24. Never leave the appliance switched on unattended. If you 

leave the work area, switch the appliance off or unplug it 

from the receptacle (don’t pull the cord, but use the plug).

25. In order to protect children from electric household 

appliances, make sure that the cable can’t cause children 

to stumble and don’t give children access to the appliance.

26. Never use the appliance when you are under the influence 

of medication, alcohol or drugs, if you are currently under 

medical care, or if you are tired.

27. Check the appliance and the power cord regularly for any 

possible damage. Don’t use damaged appliances.

28. Don’t try to repair the appliance yourself. Always use 

an authorized technician for repairs. Always have faulty 

power cords replaced immediately by the manufacturer 

or a qualified service organization. Use the same type of 

cable in order to prevent any danger of electric shock and 

injury.

29. Only use original spare parts and accessories. Non 

approved parts or third-party accessories may be a 

possible source of danger and cause the guarantee to 

become void.

30. Check the float often.
31. If you notice liquid leaking from your appliance, switch it off 

immediately and unplug it.

32. Do not submerge the appliance in water. Make sure that 

water is not spilled on the appliance.

33. When disposing of the wastewater, make sure that you 

observe any legal regulations. 

34. Only store the appliance in a safe and dry location outside 

the reach of children.

35. Please also pay particular attention to the following 

“Additional Safety Instructions For Workshop Vacuum”.

36. This appliance is not intended for use by persons 

(including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, 

unless they have been given supervision or instruction 

concerning use of the appliance by a person responsible 

for their safety.

37. Children should be supervised to ensure that they do not 

play with the appliance.

38. If the supply cord is damaged, it must be replaced by 

the manufacturer, its service agent or similarly qualified 

persons in order to avoid a hazard.

3. This wet/dry vacuum cleaner may only be used and kept in 

a private home.

4. The appliance is designed to vacuum up materials that are 

not hazardous to your health and that are not flammable.

5. Never hold the connectors in front of your face (especially 

your eyes, ears, etc.). Never direct the nozzle towards 

persons or animals.

6. Only use the appliance for its designated purpose. Any 

other types of use are at your own risk and are possibly 

dangerous.

7. Other uses and unattended operation are not allowed. 
8.  The manufacturer cannot be made responsible for 

damages that are caused by improper use or incorrect 

operation.

9. Wear protective clothing and gloves.

10. Connect the appliance only to a 240V ~ 50Hz alternating 

current receptacle.

11. Make sure that the correct dust bag has been inserted 

securely in its holder before using the appliance. The 

wrong dust bag or incorrectly installed dust bags can 

cause damage to the appliance and cause the guarantee 

to become void.

12. If the power cord is damaged, it must be comepletely 

replaced along with the cable protector by an authorised 

service centre or other qualified service organisation.

13. Do not vacuum up ashes, hot coals and the like, large 

fragments of glass and sharp objects.

14. Dont vacuum up any printer toner dust as it is electrically 

conductive. In addition, it is possible that it will not be 

completely filtered out by the filter system of the wet/dry 

vacuum cleaner and can be released into the air via the 

exhaust fan.

15. Never vacuum flammable or poisonous liquids like petrol, 

oil, acids, or other volatile substances.

16. Don’t vacuum up liquids that are hotter than 60°C or any 

poisonous or flammable dusts.

17. Never lay the appliance on its side. Pay particular attention 

to a horizontal position and adequate stability on stairs.

18. Always unplug the appliance after use and before cleaning 

or changing the filters or accessories.

19.  Only trained specialists may make repairs on electric 

equipment. Improper repairs could result in considerable 

danger to the user.

20. Do not store the appliance directly beside a hot oven or 

radiator.

Summary of Contents for AVC-1530-G

















Reviews: