manualshive.com logo in svg

Advantech UNO-3072L, User Manual, Page: 44 / 64

Share
Download
Advantech UNO-3072L User Manual Download Page 44

UNO-3072L User Manual

36

Chapter 3  Initial Setup

3.1  Inserting a CompactFlash Card

UNO-3072L has one internal CompactFlash slot (CN3). It's used to 
install O.S and Application Program

JP2 on mainboard (refer to Figures A.4 and A.5) 

Closed: CN3 CompactFlash on mainboard is the master
Open: CN3 CompactFlash on mainboard is slave 

NOTE:   1. Only one CompactFlash can be set as master

2. Internal & external CompactFlash doesn't support Hot Swap
3. Needs to use " Fixed Disk Mode" CompactFlash to install OS 

Following is the procedure for the installing a CompactFlash card in the 
internal slot (CN3) of your UNO-3072L. Please follow these steps       
carefully:

1.

Remove the power cord.

2

.

Unscrew the four screws from the top cover of UNO-3072L.

3.

Remove the top cover.

4.

Plug a CompactFlash card with your OS and application program      

into a CompactFlash card slot on mainboard.

5.

Screw back the top cover with four screws.

3.2  Connecting Power

Connect the UNO-3072L to a 16 ~ 36 VDC power source. The power 
source can either be from a power adapter or an in-house power source.

Summary of Contents for UNO-3072L

































































Reviews:

No comments