manualshive.com logo in svg

Advantech UNO-3072L, User Manual, Page: 25 / 64

Share
Download
Advantech UNO-3072L User Manual Download Page 25

17

Chapter 2  

2.3.7 Termination Resistor (JP6)

The onboard termination resistor (120 ohm) for COM3/COM4 can be 
used for long distance transmission or device matching (Default Open).

Close: Enable termination resistor.

Note: Please refer to Figure A.4 and A.5 for location of JP6

2.4  LAN: Ethernet Connector

The UNO-3072Lis equipped with a Realtek RTL8139C Ethernet LAN 
controller that is fully compliant with IEEE 802.3u 10/100Base-T CSMA/
CD standards. The Ethernet port provides a standard RJ-45 jack on board, 
and LED indicators on the front side to show its Link (Green LED) and 
Active (Yellow LED) status.

2.5  Onboard Isolated Digital Input

The UNO-3072Lhas 4 isolated DI channels designated DI0~DI3.

2.5.1 Pin Assignments

The connector type of UNO-3072Lis plug-in screw terminal block that 
enables you to connect to field I/O devices directly without additional 
accessories. Figure 2.5 and Table 2.4 shows its pin assignment as well as 
signal description.

RS-422

RS-485

COM3

Close A

TX3-TR

Data+, Data-

Close B

RX3-TR

COM4

Close C

TX4-TR

Data+, Data-

Close D

TX4-TR

Summary of Contents for UNO-3072L

































































Reviews:

No comments