Advantech MIO-5393 User Manual Download Page 63

Page: 63 / 96

MIO-5393 User Manual

Chapter 3

MI BIOS

Setup

3.1.6

Save & Exit

Save Changes and Exit

This item allows you to exit system setup after saving the changes.

Discard Changes and Exit

This item allows you to exit system setup without saving any changes.

Save Changes and Reset

This item allows you to reset the system after saving the changes.

Discard Changes and Reset

This item allows you to rest system setup without saving any changes.

Save Changes

This item allows you to save changes done so far to any of the options.

Discard Changes

This item allows you to discard changes done so far to any of the options.

Restore Defaults

This item allows you to restore/load default values for all the options.

Save as User Defaults

This item allows you to save the changes done so far as user defaults.

Restore User Defaults

This item allows you to restore the user defaults to all the options.

Boot Override

Boot device select can override your boot priority.

Summary of Contents for MIO-5393

































































































Search results

Summary of Contents for MIO-5393

Reviews:

Related manuals for MIO-5393

Brands by name

Popular brands

Advantech MIO-5393, User Manual

Search results

Summary of Contents for MIO-5393

Reviews:

Related manuals for MIO-5393

Brands by name

Popular brands