Advantech MIO-5393 User Manual Download Page 30

Page: 30 / 96

MIO-5393 User Manual

Boot Performance Mode

Select the performance state that the BIOS will set before OS handoff.

Intel

SpeedStep

Allows more than two frequency ranges to be supported.

Intel

Speed Shift Technology

Enable/Disable Intel

Speed Shift Technology support.

HDC Control

Enable/Disable Intel HDC.

Turbo Mode

Enable/Disable processor turbo mode.

View/Configure Turbo Options

View and Configure Turbo Options.

Config TDP Configuration

Config TDP Configuraitons.

Platform PL1 Enable

Enable/Disable Platform Power Limit 1 programming.

Platform PL2 Enable

Enable/Disable Platform Power Limit 1 programming.

Power Limit 4 Override

Enable/Disable Power Limit 4 override.

C States

Enable/Disable CPU Power Management.

PowerLimit 3 Settings

Power Limit 3 Settings.

CPU Lock Configuration

CPU Lock Configuration.

Summary of Contents for MIO-5393

































































































Search results

Summary of Contents for MIO-5393

Reviews:

Related manuals for MIO-5393

Brands by name

Popular brands

Advantech MIO-5393, User Manual

Search results

Summary of Contents for MIO-5393

Reviews:

Related manuals for MIO-5393

Brands by name

Popular brands