manualshive.com logo in svg

Advanjet HV-9500 Series, Maintenance And Repair, Page: 12 / 26

Share
Download
Advanjet HV-9500 Series Maintenance And Repair Download Page 12

 

Page 12 of 26 

Advanjet HV-9500 Maintenance and Repair 

3A5910A 

2.4 

Remove Heater Block Assembly 

 

 KEEP

 

 these parts to reinstall. Do not discard screws. 

A checklist of saved parts and screws is provided in section 2.6. 
 

 

BK-2001/HK-9500

 

 kit replaces these parts.  

 
 

2.4a

 

BK-2001 Heater Bushing Kit 

 

Use the #1 PH to remove the two screws 
securing the heater block; set the screws 
aside. Keep the heater block attached.  

 

Remove and discard the jet hammer spring, 
the heater block bushing, and the heater seal 
and washer. 

 
 

 
 

2.4b

 

HK-9500 Heater Block Kit 

 

Use the #1 PH to remove the two screws 
securing the heater block. 

 

Remove and discard the jet hammer spring, 
the heater block bushing, and the heater seal 
and washer. 

 

Disconnect the heater cable from the solenoid 
and the jet cable and remove. 

 

 

If only the BK-2001 or HK-9500 kit is being installed, 

 skip to section 3.3. 

 

 

 

 

KEEP 
ATTACHED

 

 

KEEP 
SCREWS

 

 

BK-2001 

 

HK-9500 

 

Summary of Contents for HV-9500 Series



























Reviews:

No comments