Advanjet HV-9500 Series Maintenance And Repair Download Page 26

 

 

Graco Standard Warranty 

Graco  warrants  all  equipment  referenced  in this  document  which  is  manufactured  by Graco  and  bearing  its  name to  be  free from 
defects  in  material  and  workmanship  on  the  date  of  sale  to  the  original  purchaser  for  use.  With  the  exception  of  any  special, 
extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace 
any  part  of  the  equipment  determined  by  Graco  to  be  defective.  This  warranty  applies  only  when  the  equipment  is  installed, 
operated a

nd maintained in accordance with Graco’s written recommendations.  

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused 
by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or 
substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility 
of  Graco  equipment  with  structures,  accessories,  equipment  or  materials  not  supplied  by  Graco,  or  the  improper  design, 
manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.  

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for 
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The 
equipment  will  be  returned  to  the  original  purchaser  transportation  prepaid.  If  inspection  of  the  equipment  does  not  disclose  any 
defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, 
and transportation.  

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT 
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no 
other  remedy  (including,  but  not  limited  to,  incidental  or  consequential  damages  for  lost  profits,  lost  sales,  injury  to  person  or 
property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within 
two (2) years of the date of sale.  

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR 
A  PARTICULAR  PURPOSE,  IN  CONNECTION  WITH  ACCESSORIES,  EQUIPMENT,  MATERIALS  OR  COMPONENTS  SOLD 
BUT  NOT  MANUFACTURED  BY  GRACO.

  These  items  sold,  but not  manufactured  by  Graco  (such  as  electric motors, switches, 

hose,  etc.),  are  subject  to  the  warranty,  if  any,  of  their  manufacturer.  Graco  will  provide  purchaser  with  reasonable  assistance  in 
making any claim for breach of these warranties.  

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment 
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, 
breach of warranty, the negligence of Graco, or otherwise.  

FOR GRACO CANADA CUSTOMERS  

The  Parties  acknowledge  that  they  have  required  that  the  present  document,  as  well  as  all  documents,  notices  and  legal 
proceedings  entered  into,  given  or  instituted  pursuant  hereto  or  relating  directly  or  indirectly  hereto,  be  drawn  up  in  English.  Les 
parties  reconnaissent  avoir  convenu  que  la  rédaction  du  présente  document  sera  en  Anglais,  ainsi  que  tous  documents,  avis  et 
procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures 
concernées.  

 

Graco Information

 

Sealant and Adhesive Dispensing Equipment  

For the latest information about Graco products, visi

www.graco.com

. 

For patent information, see 

www.graco.com/patents

.

 

For customer service and technical assistance, e-mail [email protected]  

TO PLACE AN ORDER

, contact your Graco distributor, go to www.graco.com and select “Where to Buy” 

in the top blue bar, or call to find the nearest distributor.  

If calling from the US: 800-746-1334

 

If calling from outside the US: +1-760-294-3392  
 
 

All written and visual data contained in this document reflects the latest product information available at the time of publication. 

Graco reserves the right to make changes at any time without notice. 

Original instructions. This manual contains English. MM 3A5910 

Graco Headquarters:

 Minneapolis 

International Offices:

 Belgium, China, Japan, Korea 

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA 

Copyright 2016, Graco Inc. All Graco manufacturing locations are registered to ISO 9001. 

www.graco.com

 

Revision A, August 2018 

Summary of Contents for HV-9500 Series



























Reviews: