manualshive.com logo in svg

ADS-tec StoraXe PowerBooster GSS0608, Manual

Share
Download
ADS-tec StoraXe PowerBooster GSS0608 Manual Download Page 68

 

 

Installation 

Page 

46

 of 

72 

GSS0608

 

Version: 1.3 

Basic procedure for inserting battery modules: 

 

F

IGURE 

19:

 

P

OSITIONING THE BATTERY MODULE

 

 

•

  Place the battery module on the 

support rails of the lifting 

equipment and position at the 

intended installation height. Note 

the order of installation when 

doing so.  

 

•

  Push the module halfway into the 

rack. 

 

 

 

F

IGURE 

20:

 

I

NSERTING THE BATTERY MODULE INTO THE 

RACK

 

 

 
 

•

  Slide the battery module into the 

rack until it is flush. 

 

F

IGURE 

21:

 

S

CREWING ON THE BATTERY MODULE

 

 

•

  Using 2 Nm of torque, fix the 

modules on the front side with 

the socket head cap screws 

provided.  

(M6x16 DIN 912, 4 for each 

module). 

 

 

•

  Repeat steps 1 to 3 for the 

remaining modules.  

 

 
 
 

 

 1 

 2 

 3 

Summary of Contents for StoraXe PowerBooster GSS0608













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands