background image

MODEL TYPE / SIZE 

SERIAL NUMBER 

FIG. 1 ‐ 

LISTING DATA PLATE LOCATION 

LISTING DATA PLATE / LOCATION 

 

The Adobelite Kiva Fireplace is a factory built fireplace 
tested to U.L. 127. Locate the Listing Data Plate inside the 
manifold by opening the hinged access door at the bot‐
tom of the door frame. Record the model, size, and serial 
number listed on the data plate below. 

 

PLEASE FILL IN THE FOLLOWING INFORMATION FOR FUTURE REFERENCE 

Model Type / Size: ________________ 

Frame Style: __________________________________ 

Dealership Purchased at: ______________________________________ 

Dealership Phone #: __________________________________________ 

Date Purchased:  ________________ 

Date Installed:  ___________________ 

Serial Number: ________________________________ 

Chimney Pipe Brand: ____________________________ 

Chimney Pipe Size (Inner/Outer): _______________________________ 

Notes: _______________________________________________________________________________________________________ 

_____________________________________________________________________________________________________________

_____________________________________________________________________________________________________________ 

Summary of Contents for KIVA 18 Ornito
























Reviews: