background image

12 

1)  BASE 

–Spread a thin layer of concrete mortar or construction adhesive 

on the top of the firebox pedestal. Place the firebox base on the pedes‐
tal.  Using the layout sketch, align the front of the base with the firebox 
base  line  and  center  the  firebox  along  the  center  line.  Make  sure  the 
Base is level.  

FIREBOX ASSEMBLY 

2)  LOWER  BACK 

–Apply  a  5”  wide  thin  layer  of  the  included  refractory 

mortar to the  outside top edge of the base where the Lower Back will 
rest.  Place  the  Lower  Back  in  place  and  rotate  the  piece  slightly  back 
and  forth  to  squish  the  mortar  into  place.  Align  the  back  and  sides  of 
the Lower Back and Base. 

3)  UPPER  BACK  (MODELS  KIVA24  AND  KIVA30  ONLY) 

–  Following  the 

above procedure, spread a layer of refractory mortar and place the Up‐
per  Back  section  on  top  of  the  Lower  Back.  Again,  align  the  back  and 
sides of the pieces. 

6)  TOP 

–Now install the top section of 

the  fireplace.  Again,  spread  a  thin 
layer  of  refractory  mortar  where 
the  pieces  will  meet,  and  align  the 
back and sides of the pieces. 

5)  FRONT  ARCH 

–Apply  refractory 

mortar  to  the    front  edges  of  the 
Lower  and  Upper  Back  pieces  and 
to  the  top  of  the  Front  Arch  sec‐
tion. Place the Front Arch into place 
and  attach  using  four 

1

/

4

”  x  6”  Lag 

Bolts.  Avoid  placing  any  weight 
onto the Manifold before the bolts 
are attached. 

 

6 –

Top 

2 –

Lower Back 

3 –

Upper Back 

 

 

1 –

Base 

6” Bolts

 

5 –

Front Arch 

 

4) MANIFOLD AND GAS SYSTEM 

– Apply a 1” wide layer of refractory mor‐

tar  to  the  upper  face  of  the  fireplace  base.  Position  the  Manifold  so 
that the face of the Manifold is against the face of the base, and the L‐
Bracket (that supplies combustion air) is resting on the firebrick surface 
of the Base. The Burn Pan and Kiva Grate will rest on the Base towards 
the back.  Using the supplied ¼” x 3” lag bolts, bolt the manifold to the 
Base. The heads of the bolts will pass through the face of the manifold 
and tighten against the back of the manifold. 

Do Not Over‐tighten the 

Bolts! 

Using your finger, apply refractory mortar to all the seams where 

the manifold touches the Base. 

4 –

Manifold and Gas System 

¼” dia. x 3” lag bolts 

L– Bracket 

 

Burn Pan and 
Kiva Grate 

Summary of Contents for KIVA 18 Ornito
























Reviews: