background image

Adjust-A-Sink® E140 System by Accessible Systems Inc. | Minneapolis, MN | 612-238-4600 | www.adjustasink.com

 

10 of 25 

 

 

3i.

 Adjust the base  section of 

the drain unit up about ¼” from 

full extension, centering the hose 

clamp between the marks made, 

and tighten the hose clamps. 

Move the sink to both up  &  down 

extremes  to  check  for  binding. 

Make  any  minor  adjustments  to 

eliminate  any  binding  before 

proceeding.   

 

NOTE: When the unit is installed 

at the recommended height, the 

bottom of the drain should be 

between 11” and 12” from the floor 

when correctly positioned. 

 

 

 

 

 

 

 
3J. 

Dry fit the bottom of the 

Telescoping Drain to the 

wastewater drain pipe using a 

UPC approved P-Trap or a hair 

trap (not supplied).    The outlet 

is 1-1/2” FPT.  Use appropriate 

plumbing methods to seal and 

secure  the P-trap to the drain 

and the roughed in waste outlet.   

Do not glue the P-Trap until 

you  conduct the Initial Testing 

Procedure on the following 

page.

 

 

 

 

CAUTION:  

Consider proper alignment when performing the final connection of the P-Trap to the 

Telescoping Drain and wastewater drain pipe.  The Telescoping Drain cannot be allowed  to bind; the 

motion should be smooth and continuous.  After P-Trap installation and proper alignment  and smooth 

action is achieved, connect the tailpiece nut to the basket strainer and tighten all  associated hardware.  

Use the included rubber gasket between the tailpiece and basket strainer. 

 

 

IMPORTANT: Do not trim or alter the Telescopic Drain in any way.  All components that make  up  the 

Telescopic Drain Pipe Subassembly are integrated and work together. Altering its design, or removing 

the lubricant will cause premature if not  total failure of the telescopic drain mechanism and VOID the 

warranty.

 

Secure drain 

between the 

marks 

Summary of Contents for E140 Series


























Reviews: