Adixen ATP 2300 M Operating Instructions Manual Download

Page: 7 / 58

GB 02917 - Edition 03 - 03/2013

1/1

A 150

Introduction to the ATP 2300 M

ATP 2300 M

A magnetically

levitated

turbomolecular pump

Five active axes

Rotor position control in 5 directions.

Unbalanced Force Rejection Control

Lowest possible levels of noise and vibration.
Automatic adjustment to any unbalance of the rotor, from very low
speed.

Maintenance free

Inert gas purge

Protect from corrosion the magnetic spindle.

Battery free

In case of a power failure, the pump motor acts like a generator
to transform the rotor energy into electrical power to supply the
controller.

Controllers

The ATP 2300 M works with the OBC controller or with the
MAGPOWER controller.
(refer to corresponding operating instructions).

adixen Vacuum Products - Operating Instructions - ATP 2300 M

Summary of Contents for ATP 2300 M



























































Search results

Summary of Contents for ATP 2300 M

Reviews:

Related manuals for ATP 2300 M

Brands by name

Popular brands

Adixen ATP 2300 M, Operating Instructions Manual

Search results

Summary of Contents for ATP 2300 M

Reviews:

Related manuals for ATP 2300 M

Brands by name

Popular brands