manualshive.com logo in svg

Adisa ADI CD 375, Technical Manual Of Installation, Use And Maintenance

Share
Download
Adisa ADI CD 375 Technical Manual Of Installation, Use And Maintenance Download Page 68

ADI CD boiler - Technical Manual 

 

    

 

68 

 

Front view of the boiler inside: 

Disconnect the electric connections and the pressure pipes: 

(a)  Pressure pipe connecting the gas valve to the venturi (just included in models ADI CD 200 and higher). 
(c)  Motor fan: electric supply connection (in the higher part of the motor). 
(d)  Motor fan: control indicator PWM 
(e)  Ionization-ignition kit: ionization electrode cap, ignition electrode cap and ground connection cable. 
(f)   Gas valve: electric supply connection. 

 

Note: (a) has fast connections (by pressing the plastic ring you can remove the pipe).

 

 
Remove the ionization-ignition kit. 
 
If the gas connection has a two-pieces coupling, disconnect it.  
 
Disconnect the two flanges of the gas valve (each flange has Allen screws of 
4 mm). 
 
Remove the nuts/screws of the flange connecting the fan-burner group to the 
boiler heat exchanger. 
 
By rotating the assembly motor-fan, you will find: 

-

 

Two gaskets between the boiler heat exchanger and the burner flange 

-

 Burner 

flange 

-

 

Gasket between the burner flange and the fan plate 

-

 Fan 

plate. 

 
Consider the minimum free height between the highest level of the boiler and 
the ceiling in order to extract/rotate the burner (see paragraph “boilers 
room”).  
 
Note: in models ADI CD 325 to ADI CD 750 the fan-burner assembly is 
rotating forward; in models ADI CD 850 and ADI CD 950, the fan-burner group is rotating backward.

(a)

 

(c, d) 

(e) 

(f)

Summary of Contents for ADI CD 375













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands