ADB F-Range L-850C Manual Download Page 33

Page: 33 / 60

F-Range Type L-850C Style 3 Inset Lights

Troubleshooting



2006 ADB Airfield Solutions, Incorporated

96A0285D

Page 5-2

Issued 04/13

Troubleshooting procedures for the F-Range inset lights are

contained here.

Problem Possible

Cause

Corrective

Action

1. Lamp not

energizing

Defective lamp

Replace lamp and film disc cutout (if

used). Refer to

Replacing

Lamp

in the

Maintenance

section.

Loose or broken contacts

Tighten or replace.

Moisture inside assembly causing

current leakage

Open up light assembly. Clean, dry, and

inspect light assembly. Replace O-ring.

Defective isolation transformer

Check transformer output current with

meter.

2. Lamp not turning

on at normal level

Continuity incorrect

Check lamp filament and wiring for

continuity.

3. Lamp output

distorted

Broken or damaged lens

Replace lens.

4. Improper color

Filter broken

Replace filter bracket assembly.

Filter bracket broken

Replace filter bracket assembly.

5. Short lamp life

Current too high

Check constant current regulator and

isolation transformer.

Water in assembly

Inspect prism. Open light assembly.

Clean, dry and inspect light assembly.

Replace O-ring.

Defective lamp

Replace lamp and film disc cutout (if

used). Refer to

Replacing

Lamp

in the

Maintenance

section.

NOTE:

Lamp interior will have a white

powdery appearance if air has entered

through a hole or crack.

Overvoltage

Check to see if lamp has black burns. If

so, check isolation transformer output

with meter. Replace isolation

transformer, if defective.

6. Distorted light

beam output

Cracked or damaged lens

Replace lens.

7. Water inside optical

chamber

Damaged or missing lens seals or top

cover O-ring

Replace both lens seals. Replace top

cover O-ring.

Cut or nick on L-823 cordset

insulation that exposes wire

Replace insulation.

Troubleshooting

Procedures

Summary of Contents for F-Range L-850C





























































Search results

Summary of Contents for F-Range L-850C

Reviews:

Related manuals for F-Range L-850C

Brands by name

Popular brands

ADB F-Range L-850C, Manual

Search results

Summary of Contents for F-Range L-850C

Reviews:

Related manuals for F-Range L-850C

Brands by name

Popular brands