ADB F-Range L-850C Manual Download Page 52

Page: 52 / 60

F-Range Type L-850C Style 3 Inset Lights

Parts



2006 ADB Airfield Solutions, Incorporated

96A0285D

Page 7-1

Issued 04/13

Section 7

Parts

To order parts, call ADB Airfield Solutions Customer Service or your

local representative. Use this four-column parts list, and the

accompanying illustration, to describe and locate parts correctly.

This subsection describes how to use the illustrated parts list covered

later in this section. It does not provide the actual parts list.

The Part Number column gives the ADB Airfield Solutions part

numbers in numerical order.

The Description column gives the part name, as well as its

dimensions and other characteristics when appropriate. Indentions

show the relationships between assemblies, subassemblies, and

parts.

Part Number

Description

Quantity

Note

xxxxxxxx Assembly

1 A

xxxxxxxx Part

xxxxxxxx

Part or Assembly

xxxxxxxx Assembly

NOTE A

The Quantity column contains the quantity required per unit,

assembly, or subassembly. The code AR (As Required) is used if the

part number is a bulk item ordered in quantities or if the quantity per

assembly depends on the product version or model.

The Note column contains letters that refer to notes at the end of

each parts list. Notes contain special ordering or product/part version

information.

Introduction

Using the Illustrated

Parts List

Summary of Contents for F-Range L-850C





























































Search results

Summary of Contents for F-Range L-850C

Reviews:

Related manuals for F-Range L-850C

Brands by name

Popular brands

ADB F-Range L-850C, Manual

Search results

Summary of Contents for F-Range L-850C

Reviews:

Related manuals for F-Range L-850C

Brands by name

Popular brands