ADB F-Range L-850C Manual Download Page 22

Page: 22 / 60

F-Range Type L-850C Style 3 Inset Lights

Installation



2006 ADB Airfield Solutions, Incorporated

96A0285D

Page 3-1

Issued 04/13

Section 3

Installation

WARNING:

Allow only qualified personnel to perform the

following tasks. Observe and follow the safety instructions

in this document and all other related documentation.

This section provides instructions for installing the L-850C F-Range

inset lights. Refer to airport project plans and specifications for the

specific installation instructions. The installation shall conform to the

applicable sections of the National Electric Code and local codes.

Each unit is individually packaged in a durable, cushioned, corrugated

cardboard carton. To avoid unnecessary damage to the light

assembly, unpack the carton at the installation site.

To unpack the carton, open the flaps and carefully remove the top

packing material. Thread an eyebolt into each of the two opposite

threaded holes. Run a rod through the eyebolts and lift the light

assembly from the shipping carton. Set the light assembly in a

protected area.

If damage to any equipment is noted, file a claim form with the

carrier immediately. The carrier may request to inspect the

equipment.

The F-Range light fixture is designed for connection to a 6.6 A or 20 A

series lighting circuit via an L-830 isolation transformer. Refer to

Specifications

in the

Description

section for required isolation

transformers.

Introduction

Unpacking

Input Requirement

Summary

Summary of Contents for F-Range L-850C





























































Search results

Summary of Contents for F-Range L-850C

Reviews:

Related manuals for F-Range L-850C

Brands by name

Popular brands

ADB F-Range L-850C, Manual

Search results

Summary of Contents for F-Range L-850C

Reviews:

Related manuals for F-Range L-850C

Brands by name

Popular brands