ADB F-Range L-850C Manual Download Page 42

Page: 42 / 60

F-Range Type L-850C Style 3 Inset Lights

Repair



2006 ADB Airfield Solutions, Incorporated

96A0285D

Page 6-9

Issued 04/13

Put the filter spring (10) back in. Make sure the curved part

of the filter spring faces the filter.

Latch the retainer spring (12) back on the lamp.

If a film disc cutout is used, remove the film disc cutout by

loosening the screw that secures that cutout clip to the terminal

block and rotate the cutout clip free. Refer

to Replacing Film Disc

Cutout Assembly

in this section.

Replace the film disc cutout with a new cutout by performing the

following procedure:

Position a new disc with small button side up in the terminal

block.

Rotate the cutout clip on top of the cutout and hold while

tightening the screw.

Make sure that the pressure applied by the clip on the film

disc is sufficient to ensure good contact. If loosened, remove

the clip and bend it slightly to increase its pressure.

See Figure 6-4. If the optical bracket grommets (4) are aged or

damaged, replace them, and use screws (5) to reinstall

grommets.

Reinstall optical unit into inner pan assembly. When plugging

fast-on connectors to terminal blocks, make sure there is good

contact between fast-on connectors and terminals.

Refer to Table 6-2 for parts referred to in Figure 6-10.

Table 6-2 Parts List for Replacing Film Disc Cutout

Item Part

Number

Description

Quantity

Note

Terminal block assembly

See note.

44A6112-1

Terminal block assembly, without film disc cutout

44A6112-2

Terminal block assembly, with film disc cutout

47A0118

Film disc cutout

See note.

4071.50.130

Film disc cutout clip

See note.

7110.08.367

Spring clip screw

See note.

NOTE A: Quantity is 1 for unidirectional, 2 for bidirectional.

3. Replacing Lamp and
Filter

(contd.)

Replacing Film Disc

Cutout Assembly

Summary of Contents for F-Range L-850C





























































Search results

Summary of Contents for F-Range L-850C

Reviews:

Related manuals for F-Range L-850C

Brands by name

Popular brands

ADB F-Range L-850C, Manual

Search results

Summary of Contents for F-Range L-850C

Reviews:

Related manuals for F-Range L-850C

Brands by name

Popular brands