ADB Safegate RELIANCE User Manual Download | Manualshive

Page: 50 / 76

background image

4. Insert the new connection board with the isolation board on the top cover.
5. Connect the cables to the connection board.
6. Connect the connection board with the isolation board on the top cover.

Note

There are two different types of connectors (entry cables) that are led from the converter to the LED board (and

not to the LED modules). The black one (4 pieces of 70 mm each) connect the connection board with the LED

boards and the red connectors (2 pieces of 180 mm each) connect the connection board with the converter. The

cables are available separately in a cable kit.

Figure 18: Two connector types (replaceable)

RELIANCE Omni Light
Maintenance

40
Copyright

©

ADB SAFEGATE, All Rights Reserved

«
...
48
49
50
51
52
...
»

Summary of Contents for RELIANCE













































































Reviews:

No comments

Related manuals for RELIANCE

Brand: MADRIX Pages: 36

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Samsung Pages: 20

Brand: Dantherm Pages: 96

Brand: Camozzi Pages: 33

Brand: Camozzi Pages: 2

Brand: Camozzi Pages: 64

Brand: QUAD Pages: 17

Brand: fadini Pages: 16

Compact Comfort VAV12

Brand: SAI HVAC Pages: 16

Brand: saia-burgess Pages: 203

Brand: Sailor Pages: 1

Brand: Keba Pages: 16

Brand: KEB Pages: 16

Brand: POLA Pages: 2

Brand: Gardigo Pages: 6

Brand: VAT Pages: 14

Brand: Paser Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands