ADB Safegate RELIANCE User Manual Download | Manualshive

Page: 46 / 76

background image

3. Connect the LED-cable(s) to the LED-board(s), note the cable orientation in the figure.

Note

Refer to

Figure 15: LED board

4. Assemble the light fixture.

6.4.6 Replacing the Top Cover

NOTICE

Top covers are delivered without the LED boards. LED boards have to be ordered separately.

Note

When a top cover is replaced, new LED boards (which are mounted on the brackets) have to be mounted. For LED

board replacement new gaskets and blue spacers are required. They are available separately.

1. Open the light: Disconnect the top cover from the bottom cover.

RELIANCE Omni Light
Maintenance

36
Copyright

©

ADB SAFEGATE, All Rights Reserved

«
...
44
45
46
47
48
...
»

Summary of Contents for RELIANCE













































































Reviews:

No comments

Related manuals for RELIANCE

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: Rain Bird Pages: 48

Brand: Bang & Olufsen Pages: 36

Brand: Mad Catz Pages: 4

Brand: ECKELMANN Pages: 178

Brand: Taco Electronic Solutions Pages: 28

FSDrive-MV1000 Series

Brand: YASKAWA Pages: 260

Brand: YASKAWA Pages: 114

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 152

Brand: YASKAWA Pages: 66

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 17

Brand: YASKAWA Pages: 58

J1000 CIMR-JC series

Brand: YASKAWA Pages: 2

Brand: YASKAWA Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands