Adaptec 5ANA-940 User Manual Download Page 114

Page: 114 / 152

A-4

ANA-5910/5930/5940 User’s Guide

Features Summary

The following table contains a summary of the features for the
adapter. Some of these features have not been described in detail
anywhere in this user’s reference:

General Features

ATM Connectivity and Features

Highly integrated components for
maximum life

Onboard high-speed memory,
either 512 KByte

Software diagnostics with cell error
statistics reporting

LED on the ANA-5930/5940 lights
when the ATM cable is connected
to the active adapter and another
active ATM device or loopback
mode

Supports high bandwidth
applications for video, voice,
image, and data communication

Meets all regulatory agency
requirements for world-wide
distribution

Physical media support:

■

STP, UTP-3, or better copper
cable up to 100 meters on the
ANA-5910

■

UTP-5 copper cable up to 100
meters on the ANA-5930

■

MMF optical interface up to 2
KMeters with the SC connectors
on the ANA-5940

Data Transfer Rate Over ATM
Network:

■

25.6 Mbits/sec on the ANA-5910

■

155 Mbits/sec on the
ANA-5930/5940

Up to 1024 virtual channel
identifiers (VCIs) depending on
your implementation

VC multiplexing

AAL 5 PDU data format and non-
AAL5 as raw cells

Up to 8 transmit channels
simultaneously with traffic
shaping

F4 and F5 Flow Operations and
Maintenance (OAM) cells are
supported

User-selectable PCR on each PVC

Summary of Contents for 5ANA-940

























































































































































Search results

Summary of Contents for 5ANA-940

Reviews:

Related manuals for 5ANA-940

Brands by name

Popular brands

Adaptec 5ANA-940, User Manual

Search results

Summary of Contents for 5ANA-940

Reviews:

Related manuals for 5ANA-940

Brands by name

Popular brands