Adaptec 5ANA-940 User Manual Download Page 9 | Manualshive

Page: 9 / 152

background image

1-1

1

▼ ▼ ▼ ▼

Getting Started

This document contains information on installing and configuring
the Adaptec

®

ANA

™

-5910/5930/5940 adapters. These adapters

provide the interface between your computer ’s PCI bus and a
network that uses Asynchronous Transfer Mode (ATM). Procedures
in this document describe installing the adapter, installing and
configuring the adapter drivers, and performing administrative and
management functions for your ATM network.

Note:

The procedures in this document assume that you are

connecting the adapter to an external ATM local area
network (LAN) switch.

System Requirements

Certain hardware and software components are required to use the
ANA-5910/5930/5940 adapters.

Hardware Requirements

The minimum hardware system requirements are as follows:

■

PCI rev. 2.0-compliant computer with +5V PCI slots for the
ANA-5910 and +5V/+12V PCI slots for the ANA-5930/5940

■

An available PCI bus master slot

«
...
7
8
9
10
11
...
»

Summary of Contents for 5ANA-940

























































































































































Reviews:

No comments

Related manuals for 5ANA-940

Brand: U.S. Converters Pages: 12

Allen-Bradley CrossBoard 141C-G Series

Brand: Rockwell Automation Pages: 4

Brand: Patton electronics Pages: 2

Brand: F-One Pages: 2

Brand: Hamlet Pages: 2

Brand: NEC Pages: 7

Brand: LogiLink Pages: 2

Brand: RODE Microphones Pages: 3

Brand: Rosewill Pages: 12

Enercell 273-356

Brand: Enercell Pages: 1

Brand: Planet Pages: 17

Brand: Omicron Pages: 12

Brand: Hama Pages: 2

Powerline 1300 AV2 Adapter

Brand: TRENDnet Pages: 26

BasicXL BXL-NBT-AC01

Brand: nedis Pages: 16

Brand: nedis Pages: 30

Brand: nedis Pages: 2

Brand: Fujitsu Pages: 97

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands