Adaptec 5ANA-940 User Manual Download Page 124

Page: 124 / 152

B-6

ANA-5910/5930/5940 User’s Guide

E1019 ATMO_SIG: SSCOP (UNI 3.0/
3.1): VT(CC) >= MaxCC

E1020 ATMO_SIG: SSCOP (UNI 3.0/
3.1): Timer_NO_RESPONSE expiry

E1021 ATMO_SIG: SSCOP (UNI 3.0/
3.1): SD, POLL, or SDP N(S) error

E1022 ATMO_SIG: SSCOP (UNI 3.0/
3.1): STAT N(PS) error

E1023 ATMO_SIG: SSCOP (UNI 3.0/
3.1): STAT N(R) or list elements error

E1024 ATMO_SIG: SSCOP (UNI 3.0/
3.1): USTAT N(R) or list elements
error

E1025 ATMO_SIG: SSCF (UNI 3.0
only): Misuse of SSCOP, AA-
RESYNC.ind received

These messages, preceded by E1018,
are for informational purposes. No
action is required.

E1040 ATMO_SIG: Q-93B
GENERAL CONFIG FAILURE

E1041 ATMO_SIG: Q-93B
DATA_LINK CONFIG FAILURE for
PORT variable

E1042 ATMO_SIG: Q-93B SERVICE
LAYER CONFIG FAILURE for PORT
variable

E1046 ATMO_SIG: Resources
unavailable - out of memory

These errors occur when there is not
enough memory on the system.
Increase the amount of memory.

E1044 ATMO_SIG: Primitive received
with invalid SAP id

This error, while not fatal, indicates
that users are trying to use SVCs
without valid parameters. This
message is useful for debugging when
the Classical IP portion of the driver is
not working.

E1043 ATMO_SIG: SAP down - max
number of RESTARTS sent on PORT
variable

E1045 ATMO_SIG: Virtual channel
(variable) down maximum number of
Restarts sent

These messages indicate that
signalling has encountered problems
with the switch. Stop the driver, then
restart it.

Driver Console Error Message

Description

Summary of Contents for 5ANA-940

























































































































































Search results

Summary of Contents for 5ANA-940

Reviews:

Related manuals for 5ANA-940

Brands by name

Popular brands

Adaptec 5ANA-940, User Manual

Search results

Summary of Contents for 5ANA-940

Reviews:

Related manuals for 5ANA-940

Brands by name

Popular brands