background image

3-1

3

▼ ▼ ▼ ▼

Installing the Adapter

This chapter explains how to install the ANA-5910/5930/5940 
adapter and how to connect ATM cables. 

To install the adapter in a computer:

1

Turn 

OFF

 the computer and any attached devices, and 

disconnect all power cords.

2

Detach all cables from the back of the computer. 

3

Remove the cover from the computer case. Refer to your 
computer user documentation for instructions.

Caution: 

To avoid possible damage to the adapter or 

any computer components, touch the metal part of the 
computer’s power supply to discharge any static 
electricity from your clothes and body. (Use a wrist 
grounding strap if you have one.)

4

Locate an available PCI slot, and remove the slot cover, as 
shown in Figure 3-1. (Refer to the computer user 
documentation for more information.)

The PCI slot must support bus mastering and conform to PCI 
Rev. 2.0 or higher specifications. If the slot does not meet PCI 
Rev 2.0 specifications, dedicate an IRQ channel to the slot and 
specify level triggering for the slot.

!

Summary of Contents for 5ANA-940

























































































































































Reviews: