Actel Core1553 User Manual Download Page 16

Core1553BRM Demonstration Design

1 6

 

Switches 3 and 4 (Auto Mode) 

In Auto mode, switches 3 and 4 control which Core1553BRM core is the bus controller. 

01: BRM 1 is the BC, BRM 2 is RT 2.

10: BRM 2 is the BC, BRM 1 is RT 1. 

11: No BC, BRM 1 is RT1, and BRM 2 is RT 2. 

00: No BC, BRM 1 is RT1, and BRM 2 is RT 2. 

Switch 5 (Auto and Script Modes) 

In Auto and Script modes, this switch sets the autobus/loopback feature. 

1: 1553B buses are within the FPGA Loopback mode. 

0: External 1553 transceiver is used. 

Switches 6, 7, and 8 (Auto Mode)

In Auto mode, these switches set the remote terminal address to be used in the command words
sent by the bus controller. Address values can be set in the range of 000 to 111. The demonstration
configuration sets these switches to 010 (BRM core 2 is configured as remote terminal 2). 

Switches 3 through 8 (Qualification Testing Mode) 

In qualification testing mode, these switches set the RT address parity and RT address that the
single active BRM core will use in Qualification mode. Switch 3 is the parity and 4 to 8 are the RT
address.  

LEDs 

There are twelve LEDs (

Figure 2-3

) on the board used to indicate the status of the two BRM cores

and the message traffic between them. 

Table 2-1

 shows the LEDs board location and functions.

Figure 2-3 • 

LEDs on M1AFS-ADV-DEV-KIT Board

Mfr P/N :SML-512DWT86

Mfr: Rohm

Mfr P/N :SML-512DWT86

Mfr: Rohm

Mfr P/N :SML-512DWT86

Mfr: Rohm

ACTIVE LOW

Mfr P/N :SML-512DWT86

Mfr: Rohm

V3P3

V3P3

LED3_N

{5}

LED2_N

{5}

LED1_N

{5}

LED4_N

{5}

LED7_N

{5}

LED8_N

{5}

LED5_N

{5}

LED6_N

{5}

LED9_N

{5}

LED10_N

{5}

LED11_N

{5}

LED12_N

{5}

R48

1.5K

R48

1.5K

D1

LED_ORANGE

D1

LED_ORANGE

R15

1.5K

R15

1.5K

R57

1.5K

R57

1.5K

D9

LED_ORANGE

D9

LED_ORANGE

R13

1.5K

R13

1.5K

R56

1.5K

R56

1.5K

D2

LED_ORANGE

D2

LED_ORANGE

D3

LED_ORANGE

D3

LED_ORANGE

R10

1.5K

R10

1.5K

D5

LED_ORANGE

D5

LED_ORANGE

R14

1.5K

R14

1.5K

R41

1.5K

R41

1.5K

D6

LED_ORANGE

D6

LED_ORANGE

D11

LED_ORANGE

D11

LED_ORANGE

D7

LED_ORANGE

D7

LED_ORANGE

R214

1.5K

R214

1.5K

R215

1.5K

R215

1.5K

D10

LED_ORANGE

D10

LED_ORANGE

R213

1.5K

R213

1.5K

D8

LED_ORANGE

D8

LED_ORANGE

D12

LED_ORANGE

D12

LED_ORANGE

R216

1.5K

R216

1.5K

D4

LED_ORANGE

D4

LED_ORANGE

Summary of Contents for Core1553







































Reviews: