Acorn Mx-5100 User Manual Download Page 5

Page: 5 / 43

1 Introduction

1.1

Standards

Advanced Electronics Ltd declares that the products identified below conform to the essential requirements
specified in the Construction Products Directive 89/106/EEC:

0786-CPD-20952

EN54-2: 1997 +A1:2006
Control and indicating equipment for fire detection and fire
alarm systems for buildings

Provided options:
-

Outputs to Fire Alarm Devices

Output to Fire Routing Equipment

Output to Fire Protection Equipment

Output to Fault Routing Equipment

Investigation Delays to Outputs

Dependency on more than one alarm signal

Fault Signals from Points

Disablement of Points

Alarm Counter

Test Condition

Standardised Input / Output

EN54-4: 1997 +A1:2002 +A2:2006
Power supply equipment for fire detection and fire alarm
systems for buildings

Mx-5100, Mx-5200, Mx-5400, MX-5800
Mx-5100V, Mx-5200V, Mx-5400V, MX-5800V
Mx-5100N, Mx-5200N, Mx-5400N, MX-5800N

In addition, the products comply with the following:

Low Voltage Directive 2006/95/EC

BS EN60950-1: 2006

Safety of information technology equipment

Electromagnetic Compatibility Directive 2004/108/EC

BS EN55022: 1998

Emissions, Class B

BS EN50130-4: 1996 +A2: 2003

Immunity, Product Family Standard

www.acornfiresecurity.com

Summary of Contents for Mx-5100












































Search results

Summary of Contents for Mx-5100

Reviews:

Related manuals for Mx-5100

Brands by name

Popular brands

Acorn Mx-5100, User Manual

Search results

Summary of Contents for Mx-5100

Reviews:

Related manuals for Mx-5100

Brands by name

Popular brands