1-8
Hardware Specifications and Configurations
Power Supply Electrical Design Feature
0
135W/180W in stable mode (Acer Assign System Power Unit)
EPS 2.0 (The maximum no-load power consumption for EPS 2.0 is 0.5W or less for
adapters with an output power of 50W to 250W)
Input:100~240V~2.4A 50~60HZ
Output:19V 7.1A (135W); 19V 9.5A (180W)
Security Feature
0
Kensington lock
Thermal Feature
0
Adequate venting in the rear of chassis
Must Follow Thermal engineering requirement v2.2 RFW in Appendix.
EMI Considerations
0
Metal shielding for MB (includes VGA card), touch panel control board.
Apply aluminum foil between heatsink and VESA mount.
The outside jacket of converter cable, LVDS cable, DVI cable and webcam cable are
applying conductive tape, and they fixed on basepan by conductive tape.
The ground tab which on RJ45 has to contact with MB shielding.
Gasket on MB shielding button side for increase contact area between USB connector
and MB shielding.
Acoustic Criteria
0
Operating mode: 35 dBA or under (under Windows OS)
Idle mode: 28 dBA or under (under Windows OS), please refer to Acer test summary
for details
Must Follow DT ATX acoustic Engineering RFW V1.2 in Appendix
Shock & Vibration Test Criteria
0
Operating
frequency 5 ~ 350 Hz
Acceleration 0.26 G
Sweep Rate 0.5 Octave/Minute
Endurance Cycle 1 Cycle (2 sweeps)
Test Axis: All possible operating orientation.
Test Time: 23 minutes
Vibration Unpackaged test (Random)
Frequency 5 ~ 500 Hz
Summary of Contents for Aspire Z3170
