background image

 

10

Step 13 Test Heat Alarm portion of the System  
 

Check your settings, the Default Hot Temperature setting is 90 Degrees Fahrenheit. 
(32◦c), The Stall monitor should be enabled only if a stall sensor has installed.  

To review or change these settings enter Menu mode See the User Guide. 

Test Procedure for K9 Heat Alarm  Pro  HA-2520

 

 
1)

 

Power.

 The Default Power Settings is Heat Alarm ON with Ignition. When Ignition is 

turned ON, the Heat Alarm will power up. 

 

2) System Status.

 Observe the Temperatures and Vehicle’s Battery Voltage. The Hot Status 

light will be illuminated when the Displayed Temperatures are below the Heat Alarm Hot Set 

Point and the System in not in Snooze Mode.   

 

3) System Output Test.

 Press the MENU key (for a second) to review or change the 

Feature Settings or Power Settings. Use the arrow keys to scroll through the Menu. The last 
Menu choice is "

System Test"

, Press OK to start test of all the installed Heat Alarm Alert 

options. Verify that ALL the installed Heat Alarm Alert Options worked. Follow remaining 
prompts to check control head function. 

*New AceWatchDog

 systems need configuration by the end user. See AceWatchDog 

instructions to verify that it’s connected to the network. 

 
4) Test Temperature Sensors.  

With the 

Hot Status light illuminated, 

Turn the Vehicle’s 

Climate Control to the Heat Position to manually raise the Temperature inside the vehicle. 
Monitor the Temperatures displayed on the heat alarm and confirm that the alarm activates 

when the Hot Set Point is reached 

(Center Temperature is the average of left and right 

sensors when the Average Temperature exceeds the hot or cold set points the alarm will 

Sound after the Pre Alert.)

 Return the Vehicles Climate Control to the appropriate position. 

DO NOT HEAT TEMPERTURE SENSORS WITH HEAT GUN OR FLAME TO TEST!

 

 
 
 

 
 

 

If any of these tests fail please check the installation. 

Contact AceK9.Com Support with the Serial Number, Call 772-600-7574   

Be sure K9 handler receives a copy of the User Manual. 

 

Acek9.com  Two (2) Year Limited Warranty   

For details visit http://www.acek9.com 

 

 
 
 
 
 
 
 
 

Summary of Contents for HA-2520















Reviews: