background image

 
 

                                                                                                                             

User’s Manual

 

 

9

  It is necessary to scan LED Units for all parameters before entering the Setup With Answer. 

And the scanning time depends on numbers of units. User should try again according a hint 
menu when some errors occur. 

 

If you move the cursor to the top-left corner and press the multi-selector, LCD will show you: 

 

 

 

                                                                                                       

 

                                                                                           

 

*For your reference, we respectively take the RGB, AUTO and MANUAL modes for example: 

(1)  RGB Work Mode:   

In RGB, C&B or COLOR Work Mode, user can rotate the multi-selector clockwise or anticlockwise 
to select relevant items (Unit Group: 1~100,

 

Unit Number: 1~999,

 

Glide Effect: Yes/No, Address Set: 

1~512). And then press the multi-selector to confirm your setting.       

 
 

                                             

 

                                                   

                                                                 

Select the “Confirm” item and press the multi-selector, LCD will show you the above display. 

(When adjusting relevant parameters, the being-controlled LEDs will respond sensitively.     

The LEDs will briefly flash for several seconds during data sending.)   

 

(2) AUTO Work Mode:

 

If you set the Work Mode as “AUTO”, the LCD-display will immediately show you as below: 

 

 

 
 
 
 
 

 

 

 

You can rotate the multi-selector clockwise or anticlockwise to select relevant item, then use the 
multi-selector to adjust or confirm your setting.     

In the 

AUTO Work Mode

, relevant parameters are as below: 

Unit Group:

 1-100 

Unit Number:

 1-999 

Preset Programs:

 Programs 1-10 and Program “AUTO” (a sequence of these 10 programs.)                      

Auto Speed:

 1-100. 

Setup With Answer

 

LED Unit Setup 

Data Sending

 

Please Wait…

 

When the cursor is at this position, 

pressing the multi-selector will return 

to the above display page(II). 

<

 

Confirm

     

LED Unit Setup Quit

 

 

 

Data will be lost! 

 

 

                   

Cancel

 

When the cursor is at this position, 

pressing the multi-selector will return 

to the above display page(I). 

<

 

ID: 

XXX…  

 

     

 

 

>

 

 

Unit Group:   

XXX

   

 

>

 

     

Unit Number: 

XXX 

 

 

>

 

Work Mode:

 

AUTO 

 

Auto Program: xxx

   

 

>

 

 

Auto Speed: 

 

xxx 

 

 

Auto Fadetime:xxx% 

>

 

 

Confirm to send 

 

 

 

Work Mode:  RGB

>

     

Glide Effect: 

 

XXX

 

>

 

 

Address Set:

 

XXX

 

>

 

 

Confirm to send

 

 

Summary of Contents for XB-R1















Reviews: